A 900-VA 230/115-V transformer has been tested to determine its equivalent circuit. The results of thetests are shown below. VOC = 230 V IOC = 0.45 A POC = 30 W VSC = 19.2 V ISC = 8.9 A PSC = 42.5 W All data given were taken from the primary side of the transformer. (a) Find the equivalent circuit of this transformer referred to the low-voltage side of the transformer. Rc = v omh Xm`= v ohm Req`= v ohm Xeq`= v ohm (b) Find the transformer's voltage regulation at rated conditions and (1) 0.8 PF lagging, VR%= v % (2) 1.0 PF, VR= v % (3) 0.8PF leading. VR%=

A 900-VA 230/115-V transformer has been tested to determine its equivalent circuit. The results of thetests are shown below. VOC = 230 V IOC = 0.45 A POC = 30 W VSC = 19.2 V ISC = 8.9 A PSC = 42.5 W All data given were taken from the primary side of the transformer. (a) Find the equivalent circuit of this transformer referred to the low-voltage side of the transformer. Rc = v omh Xm`= v ohm Req`= v ohm Xeq`= v ohm (b) Find the transformer's voltage regulation at rated conditions and (1) 0.8 PF lagging, VR%= v % (2) 1.0 PF, VR= v % (3) 0.8PF leading. VR%=

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 1. If a 0.6 accuracy class current transformer has a phase angle of + 10 at 100% rated current, the…

A: Ans.(1). Value of 'β=10'

Q: If the secondary side of a dual-voltage single phase transformer, as per figure 1, were to be…

A: The secondary side of a dual-voltage single phase transformer, as per the figure given in the…

Q: (b) A three phase distribution transformer characteristics is shown in Table Q1(b). Referring to…

A: Formula to calculate efficiency of a transformer is: η=n×KVA×cosϕn×KVA×cosϕ+Pi+n2×PCUwhere, n is…

Q: 4. Define voltage regulation of a transformer? 5. Full load copper loss in a transformer is 1600W.…

A: Since you have posted multiple questions , we will provide the solution only to the first three…

Q: The circuit for a 20-KVA, 220/3960 V, 50-Hz transformer is shown in Figure (1). The open- circuit…

Q: Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer.…

A: Transformer is the static device it work on the principle of faraday law of mutual inductance. It…

Q: i need the answer quickly

A: In this question we need to find a equivalent impedance referred to primary side and draw it…

Q: iii. No-load current 3. If the ratio of V/F has been kept constant and the observed value of…

A: Q.1) Explanation 1)When the frequency is lowered (for slower motor speed), the magnetic field…

Q: TTR 300 , What is the method of connecting the device to the transformer ?

Q: transformer

A: If we are giving dc to the transformer it won't work . transformer works on the principle of electro…

Q: losses =los ses 1. Maximum efficiency of transformer is when 2 At maximum effciency load current l2=…

Q: What conclusions you can come up with after implementing open circuit test on single phase…

A: Conclusions from open circuit test on single phase transformer

Q: An 100-kVA, 2500/125-V, 50-Hz, step-down transformer has the following parameters: R₁ = 1.50, X₁ =…

A: Given information is,Rated output k VA.Induced EMF ratio Volts.Turns ratio is .Supply frequency…

Q: explain how the type of loading affects the voltage regulation of a transformer

A: There are two type of loading possible in a transformer they are 1) inductive type loading 2)…

Q: 55 V / 220 V, 50 Hz single phase transformer, high voltage (secondary) windings are left idle and…

A: Winding resistance of the secondary referred to the primary, R2'=0.015 Ω

Q: 3.16 A single-phase, 50-k VA, 2400/240-V, 60-Hz distribution transformer has the following…

A: It is given that:

Q: transformer as shown in the figure given below. transformer is connected to form an auto A…

Q: (10 kVA, 200/20 V, 50 Hz values are written on the plate of a 1 phase transformer. The values given…

A: Given table,parameterOpen circuit test readingsV200 VA2.7 AW120 wattsAsked to find the Open circuit…

Q: A 22.5-kVA single-phase transformer is tested with a true-RMS ammeter and an ammeter that indicates…

A: Given data:Transformer capacity =22.5True-RMS reading =94APeak reading =204A

Q: Handwritten Need step I just don*t understand this. Available on internet you can see sol there but…

A: Step 1:Step 2:Step 3:Step 4:Step 5:

Q: List the main components of the transformer and explain briefly the function of thosecomponents.

A: The transformer is an electrical device used to transfer power from one circuit to another circuit…

Q: draw a three-phase transformer equivalent circuit and also explain how formulas were derived

A: This is a 3 phase transformer equ6 circuit.

Q: Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer.…

Q: 1. Explain why transformer saturation occurs at a lower voltage value when the frequency of the ac…

Q: answer

A: According to question: A) The no-load current of a transformer changes when voltage greater than the…

Q: AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with…

Q: Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer.…

Q: For this problem, each transformer is a single-phase ideal transformer with turns ratio N1:N2 =…

Q: (b) A single-phase transformer has 2000 turns on the primary winding and 500 turns on the secondary…

Q: Three-phase, 50 Hz 34500/10500 /Y connected transformer single-phase visible on the high voltage…

Q: Can efficiency be determined for a single phase transformer under open circuit test ?and if so…

A: Open circuit test on transformer: Open circuit test on a transformer is done to determine the no…

Q: Draw the general diagram of a single-phase transformer and briefly show how it works.

A: Transformer: A transformer is just a stationary device that converts electric energy from one…

Q: Write the voltage as a function of the transformer turns ratio for the following circuits respecting…

A: This question belongs to electrical machine . It is based on the concept of relation between…

Q: entage resistance and percentage reactance of a transformer are 1% and 4%, respectively. What is…

A: we need to find out voltage regulation ay power factor 0.8 lagging and 0.8 leading.

Q: Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer.…

A: Transformer is the static device it work on the principle of faraday law of mutual inductance. It…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

A 900-VA 230/115-V transformer has been tested to determine its equivalent circuit. The results of thetests are shown below.
VOC = 230 V
IOC = 0.45 A
POC = 30 W
VSC = 19.2 V
ISC = 8.9 A
PSC = 42.5 W
All data given were taken from the primary side of the transformer.
(a) Find the equivalent circuit of this transformer referred to the low-voltage side of the transformer.
Rc =
v omh Xm`=
v ohm
Reg`=
v ohm Xeg`=
v ohm
(b) Find the transformer's voltage regulation at rated conditions and (1) 0.8 PF lagging,
VR%=
v %
(2) 1.0 PF,
VR=
v %
(3) 0.8PF leading.
VR%=

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step by step

Solved in 10 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. How is the performance of a transformer measured? Why low voltage regulation and high efficiency is better? What is the meaning of positive and negative voltage regulations?
- A Transformer has primary windings as Np = 750 and secondary windings as Ns = 125. Its secondary voltage is Vs = 36V and output power of the transformer is PN= 3200W. The value of loses powers are Pcu = 43W and Pfe = 29 W. The resistance of loads are RLI = 1,250 and R12 = 0,88Q. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit: Primary winding N, turns Secondary winding Ng turns Primary current Magnetic Flux, Secondary IsL s current ISL1 'Isl2 Primary voltage Secondary voltage RL1 R12 Transformer Core (a) the primary voltage Vr, (b) the secondary load currents ISLı and Isl2 if the transformer is rated at RLI and R12, (c) the resulting secondary power PSL, (d) the resulting primary power PPl, (e) the primary load current IPL, (f) efficiency nL
The turns ratio of a particular transformer is less than 1. Where would you expect to see this type of transformer? OI. A 0 0 0 0 0 Power Plant K Generation II. A and B III. B IV. B and C V. C VI. C and A A Station High-Voltage Power Lines Transmission B Substation C Distribution Power Lines ( .00 Industrial Consumer Commercial Consumer Residential Consumer Distribution
Find the elements of the equivalent circuit attributed to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuit are 200 volts and 400 volts, respectively, with a frequency of 50 Hz. The primary no-load current at the voltage of 200 volts is 0.7 amperes and the loss of the core is equal to 70 watts. The resistance and reactance of the primary are 3.2 ohms and 1.25 ohms, respectively. The resistance and reactance of the secondary are 0.6 ohm and 0.07 ohm, respectively. Draw the equivalent circle, showing the values of its elements.
A 36/240 V phase transformer, belonging to a phase measured from the no-load (idle) run and short-circuit test. values are given in the table below. High voltage by applying rated voltage to the low voltage winding (The winding ends were left unloaded and the results of the no-load test results were obtained. By applying nominal current to the high voltage windings, the low voltage windings were short-circuited, and the results of the short circuit test were obtained. In direct current test 1 V direct voltage is applied to the low voltage winding, and the transformer draws 500 A direct current. All equivalent Calculate the circuit elements as moved to the low voltage side. Idle run test: Voltage : 36V Power : 68W Current : 2,8A Short circuit test: Voltage : 15V Power : 325W Current : 42,2A
4. Why the efficiency of the transformer is high at half load compared to full load?
Following are the results of a test carried out on a 230/600 V single phase, 7.5 kVA transformer. O.C. Test : 230 V, 1.2 A, 280 W, on L.V side S.C. Test : LV winding is shorted. 26 V, 11A, 155 W, H.V. Both the full load efficiency and full load regulation of the transformer on the side are 0.8 lagging p.f Search on.
b) The parameters of the transformer equivalent circuit are given bellow, Primary =1290. Secondary winding turns =130. The resistance of the primary winding =0.2 O. The resistance of the secondary winding =0.06 N. The leakage reactance of the primary winding =1.47 Q. The leakage reactance of the secondary winding =0.07 Q. using the above parameter values, referred to the primary winding, determine (a) Equivalent resistance, (b) Equivalent reactance, (c) Equivalent impedance and (d) The phase angle of the impedance.
1. A 1000-VA 350/140-V transformer has been tested to determine its equivalent circuit. The results of the tests are shown below. Open-circuit test Short-circuit test Voc = 235 V Vsc = 20.1 V loc = 0.57 A Isc = 9.6 A Poc = 34.3 w Psc = 42.7 W All data given were taken from the primary side of the transformer. Evaluate the equivalent circuit of this transformer referred to the low-voltage side of the transformer.
Consider the following open circuit transformer as shown in figure below which operate at: the voltage sources at no load (Voc)=170 V no load current (Ioc) = 85 m A iron losses power (Poc) = 14 W power factor = cos∅= 0.968 Compute the No load transformer parameter magnetizing (Im) and copper losses current (Ic) , (R0) and (X0) ?