1. A 1000-VA 350/140-V transformer has been tested to determine its equivalent circuit. The results of the tests are shown below. Open-circuit test Short-circuit test Voc = 235 V Vsc = 20.1 V loc = 0.57 A Isc = 9.6 A Poc = 34.3 W Psc = 42.7 W All data given were taken from the primary side of the transformer. Evaluate the equivalent circuit of this transformer referred to the low-voltage side of the transformer.

1. A 1000-VA 350/140-V transformer has been tested to determine its equivalent circuit. The results of the tests are shown below. Open-circuit test Short-circuit test Voc = 235 V Vsc = 20.1 V loc = 0.57 A Isc = 9.6 A Poc = 34.3 W Psc = 42.7 W All data given were taken from the primary side of the transformer. Evaluate the equivalent circuit of this transformer referred to the low-voltage side of the transformer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

VOLTAGE STEP UP THE VOLTAGE TRANSFORMER Done Choose... STEP UP THE CURRENT STEP UP THE VOLTAGE FREQUENCY PHASE DIFFERENCE
- A Transformer has primary windings as Np = 750 and secondary windings as Ns = 125. Its secondary voltage is Vs = 36V and output power of the transformer is PN= 3200W. The value of loses powers are Pcu = 43W and Pfe = 29 W. The resistance of loads are RLI = 1,250 and R12 = 0,88Q. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit: Primary winding N, turns Secondary winding Ng turns Primary current Magnetic Flux, Secondary IsL s current ISL1 'Isl2 Primary voltage Secondary voltage RL1 R12 Transformer Core (a) the primary voltage Vr, (b) the secondary load currents ISLı and Isl2 if the transformer is rated at RLI and R12, (c) the resulting secondary power PSL, (d) the resulting primary power PPl, (e) the primary load current IPL, (f) efficiency nL
Due to the increase in load, what change you saw in the transformer’s output power and voltage regulation?
A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be constant, the applied voltage should be ?
The rated power of a certain transformer is 1 kVA. The transformer operates at 60 Hz and 120 V ac. at 60 Hz and 120 V ac. The secondary voltage is 600 V. (a) What is the maximum current at the load? (b) What is the smallest RL value that can be excited? (c) What is the largest capacitor that can be connected as a load?
A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC voltage). Using the information provided and the "“transformer-like" relationships derived in class, estimate the corresponding load currents for the following duty ratios: a) D=0.35 b) D=0.9 c) D=0.5
b) The parameters of the transformer equivalent circuit are given bellow, Primary =1290. Secondary winding turns =130. The resistance of the primary winding =0.2 O. The resistance of the secondary winding =0.06 N. The leakage reactance of the primary winding =1.47 Q. The leakage reactance of the secondary winding =0.07 Q. using the above parameter values, referred to the primary winding, determine (a) Equivalent resistance, (b) Equivalent reactance, (c) Equivalent impedance and (d) The phase angle of the impedance.
What is transformer in electrical engineering?
The value of A =436, B=57, C =7
Which of the following statements is true about an ideal transformer? O It changes the magnitude of DC signals. O It converts DC signals into AC signals. O It converts AC signals into DC signals. O It changes the magnitude of AC signals. hp