A 500 kVA, 2300/230 V, 60 Hz transformer was open- and short-circuit tested. The data is provided below. Test Measurement Side | Voltage [V] Current [A] Power [W] Short Circuit High Voltage 100 230 9200 Open Circuit Low Voltage 230 94 2250 Determine equivalent circuit parameters for the circuit provided. If the transformer supplies a 200 kVA load at 0.95 PF lagging and 220 V on the low- a) b) voitage side, what voltage magnitude is required on the high-voltage side? 2300 V/230 V

A 500 kVA, 2300/230 V, 60 Hz transformer was open- and short-circuit tested. The data is provided below. Test Measurement Side | Voltage [V] Current [A] Power [W] Short Circuit High Voltage 100 230 9200 Open Circuit Low Voltage 230 94 2250 Determine equivalent circuit parameters for the circuit provided. If the transformer supplies a 200 kVA load at 0.95 PF lagging and 220 V on the low- a) b) voitage side, what voltage magnitude is required on the high-voltage side? 2300 V/230 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A short circuit test performed on a 25 KVA 2300/230 V transformer gives the measured value of the resistance as 0.8 Q and 0.009 Q on the two sides of the transformer. The total equivalent resistance in Q referred to LV side will be
Current transformer has Select one: O a. No relation between primary windings and its secondary windings O b. More secondary windings than its primary windings O C. Primary windings equal to secondary windings O d. More primary windings than its secondary windings
Find the elements of the equivalent circuit attributed to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuit are 200 volts and 400 volts, respectively, with a frequency of 50 Hz. The primary no-load current at the voltage of 200 volts is 0.7 amperes and the loss of the core is equal to 70 watts. The resistance and reactance of the primary are 3.2 ohms and 1.25 ohms, respectively. The resistance and reactance of the secondary are 0.6 ohm and 0.07 ohm, respectively. Draw the equivalent circle, showing the values of its elements.
Why we used isolation transformer
30-kVA, 2200/220-V, 50-Hz distribution transformer is tested for efficiencyand regulation as follows :O.C. test( Low voltage side ) : 220 V 4.2 A, 148 W S.C. test ( Low voltage side ) : 86 V 10.5 A, 360 W 1-The working current and resistance component of no-load are.........amper , .........ohm * 2-Efficiency at full-load and half the full-load at 0.8 p.f. lagging current. * 3-Equivalent resistance referred to primary & referred to secondary..........ohm , ..........ohm * 4-Regulation of transformer at 0.5 p.f. lagging current * 5-Equivalent reactance referred to primary & referred to secondary..........ohm , ..........ohm * 6-The magnetizing current and reactance component of no-load are.........amper , .........ohm *
A 36/240 V phase transformer, belonging to a phase measured from the no-load (idle) run and short-circuit test. values are given in the table below. High voltage by applying rated voltage to the low voltage winding (The winding ends were left unloaded and the results of the no-load test results were obtained. By applying nominal current to the high voltage windings, the low voltage windings were short-circuited, and the results of the short circuit test were obtained. In direct current test 1 V direct voltage is applied to the low voltage winding, and the transformer draws 500 A direct current. All equivalent Calculate the circuit elements as moved to the low voltage side. Idle run test: Voltage : 36V Power : 68W Current : 2,8A Short circuit test: Voltage : 15V Power : 325W Current : 42,2A
1. A 1000-VA 350/140-V transformer has been tested to determine its equivalent circuit. The results of the tests are shown below. Open-circuit test Short-circuit test Voc = 235 V Vsc = 20.1 V loc = 0.57 A Isc = 9.6 A Poc = 34.3 w Psc = 42.7 W All data given were taken from the primary side of the transformer. Evaluate the equivalent circuit of this transformer referred to the low-voltage side of the transformer.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Consider the following open circuit transformer as shown in figure below which operate at: the voltage sources at no load (Voc)=170 V no load current (Ioc) = 85 m A iron losses power (Poc) = 14 W power factor = cos∅= 0.968 Compute the No load transformer parameter magnetizing (Im) and copper losses current (Ic) , (R0) and (X0) ?
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.