A 5-storey building is used as an office floor for the ground, second and third levels and a private residential units in the 4th floor and an assembly area (with movable seats) in the 5th floor levels. The columns are spaced as shown. Determine the reduced live load "L" that will be carried by the highlighted column at the ground floor level. Use KLL=4.00 I I H AT -6.7m- 6.7m I- 6.7m I

A 5-storey building is used as an office floor for the ground, second and third levels and a private residential units in the 4th floor and an assembly area (with movable seats) in the 5th floor levels. The columns are spaced as shown. Determine the reduced live load "L" that will be carried by the highlighted column at the ground floor level. Use KLL=4.00 I I H AT -6.7m- 6.7m I- 6.7m I

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The simply supported I-beam is to carry a uniform distributed service dead load and live load totaling0.65 kips/ft over the 50 ft span, in addition to its own weight of 384 lb/ft. The beam will be pretensioned using multiple of seven-wire Grade 270 strands steel. Eccentricity is constant and equal to 12.5 in. The prestress force immediately after transfer is 432 kips. Prestress force due to time –dependent losses is equal to 267 kips. Properties of the beam cross-section: Ac = 369 in2 Ig = 50979 in4 c1 = 20.17 in c2 = 15.83 in r2=138 in2 a) Determine the concrete stress due to initial prestressing force only. f1, f2 b) Determine the concrete stress due to prestressing force plus self-weight only after all important losses occurred. f1, f2 c) Determine the concrete stress due to prestressing force and full service load after all important losses occurred. f1, f2
Find P
A long, slender structural aluminum [E = 69 GPa] flanged shape is used as a l = 9.2-m-long column. The column is supported in the x direction at base A and pinned at ends A and C against translation in the y and z directions. Lateral support is provided to the column so that deflection in the x-z plane is restrained at mid-height B; however, the column is free to deflect in the x-y plane at B. Assume that b; = 102 mm, d = 122 mm, t; = 8 mm, and t, = 6 mm. Determine the maximum compressive load P the column can support if a factor of safety of 2.9 is required. In your analysis, consider the possibility that buckling could occur about either the strong axis (i.e., the z axis) or the weak axis (i.e., the y axis) of the aluminum column. by C L 2 d Lateral B bracing L 2
Thanks
Based on the following figure determine the vertical reaction at the hinge type support for the loads shown on the beam. Consider that the dimensions are in meters. For the exercise use a value of x equal to 7.3 m, a value for the distributed load w equal to 160 N/m and a value for the force F equal to 532 N.
Instruction: Use 2 decimal places in your final answers. (Theory of Structure)
Question 1 2.5 N/m 2.5 N/m F Using the Approximate Method for Vertical Load, produce the shear force and bending moment diagram for the frame below. The height of each storey is 5 m. 2.5 N/m 2.5 N/m в H E Using the information given and calculate what will be the axial loads on 8 m G 5m the columns. D.
Check the column section shown below for an axial load of 350 kips. The column has pinned ends and is 30 ft long. The load is applied concentrically. The column is made of cast-iron, and the building was constructed in 1902. *7.5"- O 8"
Q6: If the cretical load for a Two ends fixed coulmn is 60 kN, what s the critical load for the other ends support conditions : ( show your . calculations ) a. One fixed end and one free end (flage pole )? b. Two ends pinned.? c. One fixed end and the other is pinned.?
Answer for set b only
i Am set B pls asnwer