In the design of reinforced concrete buildings, which of the following points the engineer should consider regarding the amount of reinforcing steel to be used: |- Using the minimum steel amount without considering the required amount in all sections. Il- Using the required steel amount not less. IIII- Using the maximum steel amount to ensure safety. O A. Only II O B. II & II O C.I& II O D. Only

In the design of reinforced concrete buildings, which of the following points the engineer should consider regarding the amount of reinforcing steel to be used: |- Using the minimum steel amount without considering the required amount in all sections. Il- Using the required steel amount not less. IIII- Using the maximum steel amount to ensure safety. O A. Only II O B. II & II O C.I& II O D. Only

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer number 1. Provide proper explanation.
Q- Metal moldings should be strong to resist . .... so that .... ... they operate in all parts as a single unit. Axial loads and Lateral loads O Non of them O wind loads O Live loada only
For the composite bar indicated, determine the permissible bending moment when the bar is bent about a vertical axis. Aluminum stress is 100 %3D MPa, Brass stress is 160 MPa, Eb = 105 GPa, Ea = 70 GPa Brass 6 mm Aluminum 30 mm 6 mm -30 30 mm
i need the answer quickly
A beam is made of four planks glued together. Knowing that the vertical shear in the beam is V = 500 N, determine the minimum required shear strength Tg for the glue. molinu sib boto nsini odi i Resua sode inn 50 mm, 50 mm 50 mm B D 150 mm 50 mm 150 mm 50 mm
Determine the moment of inertia of the composite are shown about x axis.
Determine the y-bar centroid of the composite figure shown. Where x1%-68; x2=100 and y3D84 x1 x2 - y
A bar having the cross section shown has been formed by securely bonding brass and ahumimum stock. Using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Aluminum Brass SO GPa Moduhus of elasticity Allowable stress 100 GPa 100 MPa 160 MPa M = kN-m 20 mm 20 mm Aluminum 20 mm Brass 46 mm 20 mm 46 mm
View Policies Current Attempt in Progress A composite beam is made of two brass [E-94 GPa] plates bonded to an aluminum [E-70 GPa] bar, as shown. The beam is subjected to a bending moment of 1850 N-m acting about the z axis. Assume b-57 mm, d₁-43 mm, d₂-9 mm. Determine: (a) the maximum bending stresses Obr. Gal in the brass plates and the aluminum bar. (b) the stress in the brass brj at the joints where the two materials are bonded together. 2 Brass (2) Aluminum (1) Brass (2) Answers: (a) abr = (b) Obrj = i i b MPa, Gal = i MPa. MPa.
Which of the following statements is true for design properties of non pre-stressed steel reinforcement as per NSCP 2015? *Can choose more than one. A. For non-prestressed bars and wires, fy shall be Es times steel strain for any value of strain. B. For tensile steel strains greater than that corresponding to fy, stress shall be Es times steel strain. C. For non-prestressed bars and wires, the stress beyond fy shall be Es times steel strain. D. For tensile steel strains greater than that corresponding to fy, stress shall be considered independent of strain and equal to fy.
Give small explanation also.
#5) GIVEN: FIND: Ix of the composite shape C12x 30