A bar having the cross section shown has been formed by securely bonding brass and ahumimum stock. Using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Aluminum Brass Moduhus of elasticity Allowable stress 80 GPa 100 MPa 100 GPa 160 MPa M = kN-m 20 mm 20 mm Aluminum 20 mm Brass 46 mm 20 mm 46 mm

A bar having the cross section shown has been formed by securely bonding brass and ahumimum stock. Using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Aluminum Brass Moduhus of elasticity Allowable stress 80 GPa 100 MPa 100 GPa 160 MPa M = kN-m 20 mm 20 mm Aluminum 20 mm Brass 46 mm 20 mm 46 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2 Calculate the bending stress at the bottom edge of the following composite beam subject to a bending moment of M= 1500 Nm. The lower section is made from steel (E = 200 GPa) and the upper section is made from aluminium (E = 70 GPa). All dimensions are in mm. 100 YA 100 Z 10 >
A composite bar consists of aluminum and steel is held by rigid supports as shown. At 57°C, an axial load of 220 kN is applied to the assembly. Determine the stresses in each of the component when the temperature is raised to 112°C. Based on laboratory results for steel, E = 210 GN/m?, a = 24x106/C, and for aluminum, E = 70 GN/m?, a = 11.8x10- 6/°C. STEEL Ø = 15cm? ALUMINUM Ø= 1Ocm? 220 kN -100 mm 150 mm Activa Go to S
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b, - 0.9 in, b2 - 2.7 in., and d- 1.8 in. The elastic modulus of the steel is E, - 30,000 ksi, and its allowable bending stress is 17 ksi. The elastic modulus of the bronze is E2 - 15,000 ksi, and its allowable bending stress is 14 ksi. Calculate the allowable bending moment that can be applied about the z centroidal axis. Bronze (2) d Steel (1) b2 Part 1 Your answer has been saved. See score details after the due date. Determine the modular ratio in order to transform the steel into an equivalent amount of bronze. Answer: n- Attempts: 1 of 1 used Part 2 Determine the area moment of inertia of the transformed section about the z-axis. Answer: in.4
A composite bar BCD has a uniform external radius Ro = 5 cm. Segment BC is solid steel, while segment CD is composed of a copper core of radius Ri = 1cm bonded inside a steel sleeve. The lengths of the two segments are LBC = 2 m and LCD = 1 m. The material moduli are Esteel = 200 GPa and Ecopper = 100 GPa. The bar is fixed at B and tensile loads are applied at section D (FD = 1000 kN) and at section C (FC = 400 kN). Compute the following: Axial stress of steel in segment BC in MPa. Axial stress of steel in segment CD in MPa. Axial stress of copper in segment CD in MPa. Total elongation of the assembly in mm.
A composite sample of carbon reinforced epoxy has dimensions of in 20 in x 20 in x 0.135 in and mass of 3 lb. The carbon fibres have a modulus of elasticity of 80(106) lb/in2 and a density of 0.15 lb/in3. The epoxy matrix has modulus of elasticity of 0.90(106) lb/in2 and a density of 0.05 lb/in3. Assume there are no voids in the sample, calculate the volume fraction of: (i) The carbon fibres (ii) The epoxy matrix in the sample.
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 73 GPa] bars, as shown. The beam is subjected to a bending moment of 445 N-m acting about the z axis. Using a = 15 mm, b = 125 mm, c = 30 mm, and d = 75 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum C Aluminum Answers: (a) Ogl Brass (b) Obr= i i b Brass a MPa MPa
3 For a composite bar as shown below, what is the relation between axial deformation and thermal deformations in the bar? Cu tube (1) Steel bar (2) D d- Where, o,, o, = stresses in Cu and steel bar respectively. Coefficient of thermal expansion for Cu and steel bar respectively.
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b1 = 0.5 in, b2 = 1.5 in., and d = 1.0 in. The elastic modulus of the steel is E1 = 30,000 ksi, and its allowable bending stress is 24 ksi. The elastic modulus of the bronze is E, = 15,000 ksi, and its allowable bending stress is 16 ksi. Calculate the magnitude of the allowable bending moment that can be applied about the z centroidal axis. y Bronze (2) Steel (1) bị b2 Answer: M = i Ib-in. Save for Later Attempts: 0 of 1 used Submit Answer
Bar A-B-C is made from a fully bonded composite of two materials as shown in the cross section below. Find the Z displacement at point C. A C 1.10 m 20 kN B 1.25 m 50 kN с Y I cross section c-c Uz = 5 mm, material 1 5 mm, material 2 5 mm, material 1 25 mm Material 1 E = 240 (GPa) Material 2 E = 180 (GPa) mm (at C)
Q1 A cantilever composite beam is formed by bonding together brass bar (EB = 100 GPa) and aluminium (EA = 70 GPa) with cross section and loading at free end as shown in Figure Q1. Parameter x, y, and z are given by: X=0 Y=0 Z=2 (a) Determine the centroid and the moment of inertia of the composite section. (b) Calculate the maximum tensile and compressive stresses in the brass and aluminium. brass 5x mm (10 mm 20mm |4y mm 0.5(4y) mm M=2.z kN.m 4y mm aluminium Figure Q1 |
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis.Modulus of elasticity 70 GPa,105 GPa Allowable stress100 MPa,160 MPa