A 5 KVA, 11000/220-V, 60 Hz, single-phase conventional transformer is supplying 2.8 KW of power to a load at 0.8 Lagging power factor, a load voltage of 220 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. +0 a Ih+es 2440 S2 Select one: O a. Vp = 13.62 KV O b. None O c. Vp 12940.4 Volts O d. Vp 14.03 KV 0.808+j 4.04 52 Ims j700.352 Is Vs 0+

A 5 KVA, 11000/220-V, 60 Hz, single-phase conventional transformer is supplying 2.8 KW of power to a load at 0.8 Lagging power factor, a load voltage of 220 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. +0 a Ih+es 2440 S2 Select one: O a. Vp = 13.62 KV O b. None O c. Vp 12940.4 Volts O d. Vp 14.03 KV 0.808+j 4.04 52 Ims j700.352 Is Vs 0+

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage reactance of 0.240. The low voltage winding resistance is 0.05 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent circuits)
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
6. 150 kVA, 2800-240 V, 50 Hz transformer. Regis = 0.0082N , Xeq.Ls = 0.0223N RfcHs=2200N Step down transformer delivers 135 kW to a load at 0.9 lagging power factor at rated voltage. Determine the Following: a) Terminal voltage (LV side). b) Terminal voltage (HV side). c) High side current. d) Input impedance. e) Voltage regulation. f) Efficiency. g) Voltage regulation for 0.9 leading pf. h) Draw the phasor diagram of secondary circuit at 0.9 lagging pf. i) Draw the phasor diagram of secondary circuit at 0.9 leading pf. XmHs=12002
Vin V₁ leee liee V₂ R₂ ww Vout 1:5 Assume the transformer circuit above is ideal, and that R₁ = 1000, R₂ = 4000 and 11,rms = 50 A. Find the rms voltage, Vzrms, across the secondary coil of the transformer. V2.rms [V]:
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
The turns ratio of a particular transformer is less than 1. Where would you expect to see this type of transformer? OI. A 0 0 0 0 0 Power Plant K Generation II. A and B III. B IV. B and C V. C VI. C and A A Station High-Voltage Power Lines Transmission B Substation C Distribution Power Lines ( .00 Industrial Consumer Commercial Consumer Residential Consumer Distribution
The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I2R loss is 1800 W and the core loss is 1500 W. Round your answer off to the nearest whole number
The rated power of a certain transformer is 1 kVA. The transformer operates at 60 Hz and 120 V ac. at 60 Hz and 120 V ac. The secondary voltage is 600 V. (a) What is the maximum current at the load? (b) What is the smallest RL value that can be excited? (c) What is the largest capacitor that can be connected as a load?
8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal. Determine the conducting and transformed currents of auto transformer. N1=200 NBC=20 N2=100 NBA=30 10A B 200 V 50,Hz C N1: N2
8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal. Determine the conducting and transformed currents of auto transformer. N1=200 NBC=20 N2=100 NBA=30 10A B 200 V 50,Hz N1 : N2 lellll
The maximum efficiency of a 200KVA, 6000/230volt, 50HZ, single phase transformer occurs at half load and is 95% at unity power factor. What is the full load efficiency at 0.7 power factor?
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.