A 5 ft -10 ft- -10 ft- 10 kips 10 kips

Q: Each of the five struts shown consists of a solid steel rod with E= 200 GPa. Given: Po = 7.2 kN 900…

A:

Q: Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What…

A:

Q: In the structure shown, an 8-mm-diameter pin is used at A, and two pins are used at B and D. Knowing…

A: Given data: pin A diameter = dA = 8 mm Ultimate shearing stress  at pin A = 100 MPa = 100 n/mm2

Q: A compression member has the cross section shown and an effec-tive length of 5 ft. Knowing that the…

A:

Q: A compression member of 1.5-m effective length consists of a solid 30-mm-diameter brass rod. To…

A:

Q: Determine the internal load of element 3. Note that elements BG and CF are independent. a = 3, b…

A:

Q: A load P is supported as shown by a steel pin that has been inserted in a short wooden member…

A: σut=145Mpa in shear

Q: Determine the critical load of a pin-ended wooden stick that is 3 ft long and has a 3/16 × 1 1/4-in.…

A:

Q: 8. The axle of a small truck is acted upon by the forces and couple shown. Knowing that the diameter…

A: Answer: The factor of safety at point H using Von-mises stress criteria is 1.3222.

Q: A rectangular column with a 4.4-m effective length is made of glued laminated wood. Knowing that for…

A:

Q: 1. Knowing that the ultimate load for cable BD (diameter is 20 mm) is 110 kN and that a factor of…

A:

Q: determine the largest load P t

A:

Q: The 2300-lb load P may be moved along the beam BD to any position between stops at E and F. Knowing…

A:

Q: Determine the critical load of a round wooden dowel that is 48 in. long and has a diameter of (a)…

A:

Q: Problem 13.1 Two wooden members of 80mm x 120mm uniform rectangular cross section are joined by the…

A:

Q: A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 ×…

A:

Q: Determine the internal load of element 3. Note that elements BG and CF are independent. a = 4, b…

A:

Q: A 1-inch brass round bar is to be used as a support for a frame. Determine the maximum load that the…

A:

Q: Q.No.02. A 100-mm long rod has a diameter of 15 mm. If an axial tensile load of 100 kN is applied,…

A: It is known that the formula of the elongation of the rod is, Given, L=100mm, d=15mm, P=100kN,…

Q: A 1-in.-square aluminum strut is maintained in the position shown by a pin support at A and by sets…

A: E = 10.4E+6 psi I = bh3/12 = 0.083333 in4 Lef = 2 Ldc Ldc = Lef/2 in.............(1)

Q: A 12-kN tensile load will be applied to a 50-m length of steel wire with E= 200 GPa. Determine the…

A:

Q: A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load…

A: length, L=10-in Sides of the block a=1.8 in,   b=1.6 in normal stress = 18 ksi…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.