Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width wif the structure- shown is being designed to support a 28-kN load P with a factor of safety of 3? 600 mm 90° 450 mm D The width wis 278 mm

Q: Q2/ Determine the maximum allowable load P that can be safely suppom 1.5 in. and b-4 in. The wood…

A: t=1.5inb=4inσfail=2ksiζfail=2ksiFOS=1.5   To-Find:- P=?

Q: Determine the maximum weight W that can be supported as shown. Cable FG has a maximum strength of…

A:

Q: The column shown below, made from medium carbon steel AISI 1040 (E = 207 GPa and Sy = 290 MPa), has…

A:

Q: n the steel structure shown in the figure, a 6 mm diameter in is used at C and 10 mm diameter pins…

A:

Q: The 2014 T6 aluminum strut is foced between the two walls at A andB. It has a 2 in. by 2 in. square…

A: Given data T1 = 22 lb-ft T2 = 42 lb-ft Area of cross section = 2 in X 2 in

Q: Determine the critical axial buckling load for an 8 3/4 x 12 inches glue-laminated column braced at…

A: In the question , given that, E = young modulus of elasticity (1.8×106psi) dimension of column ,…

Q: Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy= 200 MPa. The pin…

A:

Q: To determine: The. The critical load of the aluminum column; B. The dimension d so that the steel…

A:

Q: A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to…

A:

Q: 480 mm B D PROBLEM 1.39 Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate…

A:

Q: section. If AB is made up of aluminum and CD of steel, determine the required diameter of each…

A:

Q: The horizontal link BC is 6.35 mm thick, has a width w = 31.8 mm, and is made of steel with ultimate…

A:

Q: A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to…

A:

Q: 4-26. The truss consists of three members, each made from A-36 steel and having a cross-sectional…

A:

Q: A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to…

A: Diameter d = 20 mm Ultimate load = 150 KN F.S = 3 Required diameter of rod AD Answer is 39.79 mm

Q: The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and…

A:

Q: Determine the largest load P that can be applied to the structure shown below. All members are made…

A:

Q: Two solid cylindrical rods support a load of P = 25 kN as shown. Determine the axial load in rod…

A:

Q: Required information A 1-in.-square aluminum strut is maintained in the position shown by a pin…

A: Solution: Given Data: A=1 in2LAB=3.4 ftE=10.4×106 psiFOS=3.2   To Find; The magnitude of the…

Q: (1) L4 L3 L2 A rigid component ABC is supported by a pin-connected member (1). The member has a…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.