A 48-in. boom is held by a ball-and-socket joint at Cand by two cables BF and DAE, cable DAE passes around a frictionless pulley at A For W=390 lb, determine the tension in each cable and the reaction at C. (Round the final answers to one decimal place) 48 in. A B W The tension in cable DAE is The tension in cable BD is The reaction at Cis-( 9 20 in 16 30 in. 20 in. Ib. (Round the final answer to the nearest whole number) ib ib) i+( Jlb))+( lb) k

A 48-in. boom is held by a ball-and-socket joint at Cand by two cables BF and DAE, cable DAE passes around a frictionless pulley at A For W=390 lb, determine the tension in each cable and the reaction at C. (Round the final answers to one decimal place) 48 in. A B W The tension in cable DAE is The tension in cable BD is The reaction at Cis-( 9 20 in 16 30 in. 20 in. Ib. (Round the final answer to the nearest whole number) ib ib) i+( Jlb))+( lb) k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AB is 110 lb. (a) Determine the vertical force P exerted by the tower on the pin at A. (b) Determine the moment about point O of the Resultant Force.
a. What are the external reaction at the position of the rocker at D, the external horizontal, vertical and resultant reactions at point A? [Solve for a value in kips, with right as positive and left as negative.] b. What is the force in member BC? c. What is the minimum possible diameter of the pin at A which is double shear and the minimum possible diameter of pin B which is single shear? [in inches]
The light right-angle boom which supports the 360-kg cylinder is supported by three cables and a ball-and-socket joint at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. A Ox - Answers: IM TAC = i Me C 0.65 m y 1.05 m! 0.65 m 10 B 360 kg 1.30 m 2.30 m N Oy E 1.45 m II D N TBD = 1.45 m Hr x N O₂ = Mi N TBE = i N N
The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin) at D. Determine the reactions at the supports. Neglect the thickness of the beam. Ak 4 k 30° ܘܐܝܐ A ANAS DOLL 15 k. ft D B States Yk 3 4 Bft C ft 8 ft Aft 4 ft 2 ft 8. What is the shear at a point (A + 4) ft left of point C? (k) 9. What is the shear at a point (A + 8 + C/2) ft left of point C? (k) 10. What is the moment at point C? (k-ft) Use: A= 8 B= 6 C= 8 Y= 29
Cable Eメ了 The beam AB shown 50 weighs 10N/ m Supported by at A and B hinge 280 N and Cable at a B. Delermine The reactions at A and the tensiin in the cable
433N 296 N 127N Im Em 11m 357N Determine the forces at the reactions.
The homogeneous bar AB weighs 550 N. End B lean against a rough vertical surface and end A is supported by a ball-and-socket joint. Determine the reaction at A and B of the tension in the cable is 150 N. Z. C 30° В 5 m 6 m --- 4 m X A y
In this statics problem I am given a triangular distributed load on a cable. Attached is the given info for the problem. I know the basic steps to complete the problem but I am having issues figuring out where the triangular distributed load and 15 degrees given work into the problem. I’ve tried finding the Moment around B with the distributed load and then the two components of Tension at A (using sin(15) and cos(15) respectively but this did not work.
Determine the moments in the beam at A, B. and C. O-15 1. What is MAB in kN-m? 15 Select the correct response: 30 12 kN/m -30 5m
(3) Two beams AB and BC are pinned connected at B, fixed to wall A and supported by a roller at C. For the loading shown, determine (a) the reactions at the wall support A, (b) the internal shear force and bending moment in the beam at section D, which is located 1 m from the fixed end A. Ans: (a) Ay = 1550 N 1, M₁ = 3800 N-m CCW (b) VD=1438 N, MD = -2290 N-m A 450 N/m D 600 N 2 m 2 m B 400 N/m 2.5m
Q.1) For the frame shown in figure have a two- member (ABOC and EDC) and is pin connected at E, C and A. If a 750 N force is applied directed vertically (a) at B, (b) at D. Determine the horizontal and vertical components of reactions at pin E and A. 50 mm 170mm 125 mm C 75 WE