A 450 mm x 550 mm TIED column is reinforced with 12-20 distributed evenly on the two short sides only. The steel cover used is 70 mm. the concrete strength used is 27.6 MPa and yield strength of reinforcements is 415 MPa. Use column interaction diagram. a. Determine the possible design axial and moment capacity at eccentricity of 350

A 450 mm x 550 mm TIED column is reinforced with 12-20 distributed evenly on the two short sides only. The steel cover used is 70 mm. the concrete strength used is 27.6 MPa and yield strength of reinforcements is 415 MPa. Use column interaction diagram. a. Determine the possible design axial and moment capacity at eccentricity of 350

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The magnitude of the Ultimate moment capacity is Blank 1kN.m.
A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The nominal moment capacity multiplied by its strength reduction factor is 377kN.m. Determine the allowable concentrated live load in kN that it could carry acting at 2.25m from the support if the length of the beam is 2.57m. Note that the dead load includes the weight of the beam.
1.2m 10 cm O 7cm -7cm O This concrete beam has four A-35 steel rods of one centimeter diameter and a square cross section. It experiences a compressive axial load of 200kN. You must calculate the stresses developed in the two components in the figure.
A reinforced concrete beam is 250 mm wide with an effective depth of 400 mm. Use f'c= 21 MPa and fy = 275 MPa. The section is reinforced with 4 - $25mm bars. U = 1.2D + 1.6L. a. Compute for the nominal flexural strength. b. Calculate the design flexural strength of the section. c. Calculate the safe service live load moment if the service moment from total dead load is 96 kN-m. d. If the beam is 5m long with a moment from total dead load of 96 kN-m, find the maximum moving concentrated service live load that can be supported by the beam.
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f’c = 28 MPa fy = 276 MPa Aps = 800 mm2 Ds = 10 mm Dm = 18 mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250 kN
A rectangular beam has a width of 283mm and an effective depth of 461mm. It is reinforced with 4-25mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 285MPa. The ultimate moment capacity is ___kN.m.
A rectangular beam has a width of 298mm and an effective depth of 465mm. It is reinforced with 4-25mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 295MPa. The ultimate moment capacity is ___.
Exercises 1- A rectangular beam reinforced with 4 o18 bars has h=650mm, bw=250mm and d'=30mm. Applied moment is 67 kN.mMaterials used are C25 and S220. Allowable compressive stress and modulus of rupture for concrete are 10MPA and 2.3 N/mm2 respectively. Allowable stress for steel is 140 MPa. Is this beam cracked or uncracked? Is this beam designed adequately to carry the applied moment safely? 2- Does this beam have enough capacity to carry the applied moment? Also, calculate the position of neutral axis. h=50cm, bw= 25 cm, and d'=3cm. C25 and S420 are used. (kı= 0.85; fod= 17 MPa; fya=365 MPa; E= 2X10°N/mm?) DL= 30 kN/m LL= 15 kN/m 4Ф 22 5.3 m 3- Calculate the moment carrying capacity of the beam shown? Choose the required steel reinforcement to carry this moment. d=470mm b= 270mm and d'=30mm. C20: Allowable stress=7MPA S420: Allowable stress=220 MPa A, n=15
A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with 10-20-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. Use f’c = 21 MPa and fy = 420 MPa. Determine the nominal axial strength (kN) of the column as per NSCP 2015. Determine the required spacing (mm) of laterial ties 10-mm-dia. Determine the location of the plastic centroid (mm) measured from one short edge.
3 A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-∅20 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = ? Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ?? Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = ?
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
Design Slab DEGH of the floor system shown below. Dead load pressure including the slab's weight is estimated at 5.3 kPa while live load pressure is 2.4 kPa. Use fc' = 21 MPa and fy = 345 MPa. The supporting beam is 350 mm x 500 mm. Use 12mm diameter bars. 6m A B 6m C 2.6 m D 2.6 m 2.6 m J E H K LL F I L