A 4 m long cast iron hollow column with both ends firmly fixed supports an axial load of 400 kN. The inside diameter of the column is 0.6 times the external diameter. Determine the dimensions of the column. Assume factor of safety to be 5, crushing stress of 560 MPa and Rankine constant 1/1600.

A 4 m long cast iron hollow column with both ends firmly fixed supports an axial load of 400 kN. The inside diameter of the column is 0.6 times the external diameter. Determine the dimensions of the column. Assume factor of safety to be 5, crushing stress of 560 MPa and Rankine constant 1/1600.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Cross sectional area and section modules of a short hollow Cl column section are 200 cm2 and 2x 10^6 mm3 respectively. It carries an axial load of 400 KN and a load of 100 KN on a bracket. The load line being 250 mm away from axis of column. Minimum and maximum stress intensities are respectively- 11:16 PM FF: 10:
Find maximum normal stress in given beam section a-a. 6 = A MPa 30 kN 50 kN 50 kN 30 kN 2 m i a 5 @ 0.8 m = 4 m W310 X 52 B H
A 30 ft tall column has a cross section of 8" x 8" with 1" thick walls, (i.e., it has a 6" x 6" hole in the middle). The material has a Young's Modulus E = 2,000,000 psi, and an axial yield stress of 1600 psi. Using a crushing FOS of 1.67 and a buckling FOS of 1.9, compute the following: a) What is the LARGEST axial load this column can sustain? Hetion b) If the column is braced (in both directions) at 10 feet above the ground, what is the maximum axial load the column can sustain?
a=2 so d=4 Strength of material question need help with solution
Current Attempt in Progress Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3150 mm2 and an allowable normal stress of 175 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 1.9 m, x2 = 2.9 m, y1 = 1.4 m, and y2 = 2.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable %3D %3D normal stress. y2 A (1) В W P Answer: Pmax kN
Problem #3 (33 points) The two 500-lb forces are parallel to the y axis and the P force is parallel to the z axis. If the allowable shear stress is 8 ksi, calculate the smallest permissible diameter of the solid shaft AE. Use the Maximum Shear Stress failure theory. 7 in P 7 in 7 in 7 in 4 in 6 in 4 in 500 Ib 500 Ib
A rectangular reinforced concrete beam with width of 250mm and effective depth of 500mm Is subjected to 150kNm. The beam is reinforced with 4 – 25mm bars. Use n = 9 Kindly answer all of the said questions, thank you!
Problem #3: A circular shaft, fixed to the wall, is loaded as indicated in the figure below. Using all three failure criteria (Rankine's theory, Tresca criterion, and Von Mises criterion), determine the load magnitude, R, that causes yielding at point A on the cross-section. Assume the yield strength of the material is 64 ksi. Notes: . . ● Point A is at the mid-depth of the section and on the leftmost fiber (as viewed below). At the fixed base, the shaft will be subjected to a bending moment, a torsional moment, a shear force, and a normal force. Recall for a circular cross-section; 1=d¹ and/=d. Q does not need to be provided, as you should see herein. A 3 ft R 4 in. F T 2 ft 12R X
Current Attempt in Progress Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4650 mm² and an allowable normal stress of 80 MPa. Bar (2) has a cross-sectional area of A2 = 2800 mm2 and an allowable normal stress of 160 MPa. Assume x₁ = 1.5 m, x₂ = 3.1 m, y₁ = 1.5 m, and y2 = 2.5 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A Answer: Pmax= (1) i B (2) C kN 1/₂
6O cm 20 20. 20cm 20 cm CrOSS - section 1. Determine the value the max Yalue g mament is 702 kN. cm gbending Stress of 2. Determine the ralue sf shean SKess of the max value g shean is 420 KN -
Hand written please