The blocks of width h and height b act as a dam against water as shown in the Figure. Find the maximum stress in the blocks when the water level in the dam is 'd=2+a' and h=0,3 m. Y=9,81 kN/m³ (Specific weight of water, or weight per unit volume of water) View Blocks Plan

Q: 1 2 Add your answer Ꮎ ] Ꮎ 3 P A system of three bars with similar cross-section and material…

A:

Q: What is the shear stress in the 25-mm diameter bolt at pin C if P = 25 KN? A 50.93 MPa B 67.91 MPa…

A: Given,  dc = 25 mm  P = 25 kN

Q: 7. If Pascal (Pa) is , and kips is kilopounds , convert 2 MPa to kips/ft2-

A:

Q: They say that the 6 is the base 1 and the 7.6 is adding 6+0.8+0.8 as base2. My question is why you…

A: The expression which is shown in the solution is 12(6+7.6) here the values of geometry are…

Q: A (m)– Y (N) 2 m x (N). |C 2 m A B

A: Given Data:X=482Y=82A=9

Q: X= 482 Y= 82 A= 9   SHOW COMPLETE SOLUTIONS

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: A 100- m steel tape is used to measure the distance of the line and found to be 1539.28 m long.…

A:

Q: Brass rod diameter 6 mm is subjected to tension of 5 KN, the diameter change by 3.6* 10 mm the…

A: As per our guidelines we are supposed to answer only first question in case of multiple questions.…

Q: Solve the two sub-parts

A: Calculation of  remaining  two sub part part d - plasticity index  Part e - Liquidity Index

Q: Using force method find moment at C take Mc as a redundant 120 kN B 6 m 6 m

A:

Q: A 116.79 kips (B 172.79 kips 92.79 kips A 119.38 kips B 40 kips 1.5" V 40 kips C From the figure,…

A: dia of rod AB=2''allowable stress in rod AB=55ksi

Q: X= 482  Y=82 C=2 SHOW COMPLETE

A: X=482 Y=82 C=2

Q: plz, solve this question, it`s not graded question. Solve it as you understand. Structural…

A: Solution Degree of indeterminacy  DI=(m+r)-2j    =14+4-2×8=2Let Dy and force in member FBG be…

Q: Three consolidated-undrained tri-axial tests were performed on samples retrieved from a 4 meter…

A: GIVEN DATA :- TEST  CHAMBER PRESSUER DEVIATOR STRESS PORE PRESSURE 75 75 166 -12 150 150 295…

Q: Steel rod Steel rod A = 900 sq. mm A = 900 2 m sq. mm Copper A = 1200 2 m ww bs A B 1m 1 m

A:

Q: A triangle having a base of 1.20m and altitude of 1.8m wholly immersed in water, its base being in…

A: Length of base of triangle = 1.2m altitude of triangle = 1.8m   It has been asked in the question to…

Q: Draw the shear-force and bending-moment diagrams for the beam shown. Determine the maximum shear and…

A: Draw the shear-force and bending-moment diagrams for the beam shown. Determine the maximum shear and…

Q: What is the minimum "B" for the base of a dam 30m high if upward pressure beneath the dam is assumed…

A:

Q: For the given structural steel sections below, determine the following: a. The location of the…

A:

Q: wo smooth cylinders are placed in the position shown. Cylinder A 1,000N and has a radius of 10cm…

A:

Q: For the dam shown, determine the factor of safety against sliding and overturning. Use unit weight…

A:

Q: Problem 2. Solve the load carried by each bars.

A:

Q: rigid block of weight W is supported by three symmetrically spaced rods as shown in the Figure. Each…

A: To determine: a) The weight of W (kN) that can be supported by the system b) Actual stress in…

Q: в (m) 800 + A (N) 200 + Y (N/m) 2 m 1. Determine the horizontal reaction at A. (N) 2. Determine the…

A:

Q: The values: A=1 B=3 C=5 D=2 Note: this is complete

A:

Q: The figure shows a laterally loaded beam which is supported by two rollers and in equilibrium. Find…

A:

Q: The maximum allowable tensile force in the members of the truss is (Ft)max = 1700 lb, and the…

A:

Q: SIMPLE STRESSES 4. The puncher is to drive a 25 mm diameter hole to steel plate. If the applied…

A: Given information,    Diameter= 25 mm Applied force (axial force) = 50 kN The shear stress= 50 MPa

Q: a) What is the bearing of the course BC? b) What is the length of course DE? c) What is the…

A: To Find Missing length and bearing of the traverse. Perimeter of the traverse.

Q: Determine the internal forces (axial force, shearing force, and bending moment) at Point J of the…

A: To determine the internal force at J.   The given problem can be analyzed by drawing the free body…

Q: 10 + A (kN) 3 + B (kN/m) A B E - 3 m- – 4 m 2 m C (m) - 3 m Determine the horizontal reaction at A.…

A:

Q: A timber beam 100 mm wide by 300 mm deep is made by gluing three 100 mm x 100 mm member together.…

A:

Q: PROBLEM The centroid of the T-section shown is 2.7 inches above the base and x is 13. What should be…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.