QUESTION 5 The column is constructed from concrete and six A- 36 steel (E is 200 GPa) reinforcing rebars. If it is subjected to a compression force of 150 kN. Determine the average normal stress in the concrete and in each rebar. Each rebar has a diameter of 20 mm. 100 mm 150 kN 1.2 m

QUESTION 5 The column is constructed from concrete and six A- 36 steel (E is 200 GPa) reinforcing rebars. If it is subjected to a compression force of 150 kN. Determine the average normal stress in the concrete and in each rebar. Each rebar has a diameter of 20 mm. 100 mm 150 kN 1.2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: . Calculate the cracking moment (max. resisting moment) for the unreinforced concrete beam shown.…

A: As per Bartleby's guidelines we are supposed to answer only first question.

Q: 5. A reinforced concrete beam has a width of 250mm and an effective depth of 450mm. It is reinforced…

Q: QI Design the slabs shown in Fig (1), which is supported on rigid beams. The applied lcads are the…

A: Solution: Given: DL = 3.5 kN/m2 LL = 3.5 kN/m2 Span = 3 m fc = 28 MPa fy = 414 MPa γc = 24 kN/m3

Q: -6 The concrete post (Ec = 30 GPa and a =10x10°c) is reinforced with six steel bars, each of 10 mm…

Q: The beam-column shown below is pinned at both ends and is subjected to the loads shown. Bending is…

A: Given, PD=534 kNPL=569 kNMDTop=243 kN-mMLTop=206 kN-m MDBot=125 kN-m MLBot=64 kN-m L=4.57 m…

Q: 1.2 If concrete has an idealized compressive stress-strain relationship as shown in Fig.la for the…

A: Given: To find: The relationship between the height of equivalent stress block and neutral axis…

Q: An aluminum cylinder and a bronze cylinder are centered and secured between two rigid slabs by…

Q: 3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A…

A: A member subjected to pull is given and it has been asked to determine normal and shear stress…

Q: 1. A steel section of length L sits on an 8" x 8" bearing plate. The bearing plate is perfectly…

A: To determine,A. Determine the normal stress in the steel. B. Determine the normal stress in the…

Q: A reinforced concrete column 200mm in diamter is designed to carry an axial load of 400 kN…

A: Given data, Ec = 14 GPa Es = 200 GPa Axial load (P) = 400 kN Allowable stress in concrete = 6MPa…

Q: SHOW COMPLETE AND NEAT SOLUTIONS. (BASED FROM NSCP 2015) DETERMINE THE MAXIMUM AND CONCRETE AND…

A: We have to determine the value of maximum concrete and steel stress at the point of maximum positive…

Q: The steel pipe is filled with concrete and subjected to a compressive force of 75 kN. Determine the…

Q: A hollow circular column of steel (E = 30,000 ksi) is subjected to a compressive load P. The column…

Q: In a given reinforced concrete beam, b=300mm, d= 600mm and n=9. If a maximum stress of 5MPA is…

A: Given: Assume m=13.33

Q: 2. Determine the dimension "L" of the hollow pentagonal pedestal shown if it has to carry an ivory…

A: To find the dimension L of the Hollow Pentagon Diameter of the Hollow portion (Deven)= 35 mm…

Q: 0.5 W 0.5 W fo = 30 MPa fy = 414MPa 8. 250 mm 250 mm 3.5 m 3.5 m 2- 25mm Ø 3-36mm Ø 250 mm 300 mm

Q: determine the maximum and concrete and steel stresses at the point of maximum positive and negative…

A: Maximum bending stress The top surface of the die experiences the most bending stress, which…

Q: A 300mm x 500mm rectangular concrete beam is reinforced witl

Q: Q1) A cantilever reinforced concrete beam with rectangular section (as shown in Fig. 1) carries a…

A: P = 30KN W = 20KN/m For finding moment capacity in cracked section we have to remove steel and…

Q: What is the diameter of the grains of coarse aggregate

A: The aggregates are classified into two types based on the size, they are Fine aggregate, and Coarse…

Q: Concrete column is reinforced axially with eight steel bars as shown in fig. Each bar has a diameter…

A: Given that, P=33 kNES=180 GPaEC=12 GPaAS=Area of steel=8×(π4×252)=3927 mm2AC=Area of…

Q: A 2000-kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-sectional…

A: Determine the location x of the largest additional force P which can be applied to the bar.

Q: jected to an axial load of 1200 kN. Est = 200 GPa, Ec = 25 GPa. 1200 kN 300 mm 300 mm

A: To find stress in concrete and steel-

Q: 50 kN C 4 m w = 10 kN/m B 360 mmm 150 mmm If the maximal allowable stress is 30 MPa, is the beam…

A: Given: Ewood=12 GPaStress=30 MPa To find: Beam safe to carry the loads.

Q: -concrete rod with a cross-sectional area of andidate concretes are: (a) a=lmm, p=porosity=10%…

A: According to given data A concrete rod with a cross-sectional area of 10 cm2 is loaded in tension.…

Q: What is the value of the shear stress at the neutral axis in a rectangular section of base b, height…

Q: 1. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of…

Q: Compute the combined stress. P = 11 KN 1.5m 16KN P = 11 KN 3m L = 6m 1.5m 16KN b=50mm d=100mm

Q: AND CLEAR SOLUTION". YOU MAY BASED FROM Section at C Wox n 45 kN/m 3.0m d'u 20mm

A: P =1.6 LL+ 1.2 DL = 1.6×52+3.2×112 = 217. 6 Kn μ = 1.6×11+1.2×28…

Q: 10.1 Calculate the nominal strength P, for the section of the figure for Problem 10.1 for an…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

Q: A reinforced concrete column 500 mm x 500 mm in section is reinforced with 4 steel bars of 25 mm…

A: E for steel = 210×10^3N/mm2E for concrete = 14×10^3 N/mm2Steel bars = 4dia = 25mmColumn load= 1000…

Q: Determine maximum principal

Q: Determine the normal stress in each of the steel reinforcing rods and the maximum normal stress

Q: Problem 1.6. The ultimate stress, for a hollow steel column which carries an axial load of 1.9 MN is…

Q: An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the…

Q: A steel pod is between two rigid walls and carries a tensile load of 6000N at c. If the allowable…

A: The given data is: Tensile load, T=6000 N (At 24° C) Allowable load<130 MPa (At 24° C)…

Q: The beam with cross-section shown carries a uniformly distributed load of intensity w over its…

A: Here we find 1. Support reaction by the help of three equilibrium equation. 2. Draw shear force…

Q: A 6-in.-diameter concrete test cylinder is loaded with a compressive force of 113.1 kips, as shown…

A: Given data :The value of compressive force (F) = 113.1 kipsThe value of diameter of concrete…

Q: A round vertical steel column 500 mm in outside diameter and a wall thickness of 10mm is reinforced…

Q: 30 сm ) For the given section find the foloowing : 5 cm The ultimate maximum moment . 20 34 50 34…

A: The ultimate moment capacity is generally the moment acting on the beam and also it's capacity. The…

Q: The wood column is pinned at its base and top. Take E= 10 GPa and oy = 15 MPa (Figure 1) Figure 150…

A: Given data:- The modulus of Elasticity is, E=10 GPa σy=15 MPa The given eccentric force, P=11.8 kN

Q: Determine the maximum and concrete and steel stresses at the point of maximum positive and negative…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

COMPLETE SOLUTION WITH F.B.D. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 KN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa.
A solid circular column is 3 meters long. It is fixed at the bottom and pinned at the top. The Youngs modulus of the material is 70 GPa and the maximum allowable stress is 25 MPa. Using a factor of safety of 2.5 in calculating Eulers critical load: i. Determine the dimensions of the cross section if the column is to safely support a 100 kN load. i. Confirm the normal stress developed in the column and comment on the result.
The vertical portion of the press shown consists of a rectangular tube of wall thickness t = 10 mm. Knowing that the press has been tightened on glued wooden planks until P = 33 kN, determine the stress at (a) point 4, (b) point B. GA OB MPa MPa 200 mm 80 mm 80 mm Section a-a 60 mm B
1.1 A stainless steel tube with an outside diameter of 60 mm and a wall thickness of 5 mm is used as a compression member. If the normal stress in the member must be limited to 200 MPa, determine the maximum load P that the member can support.
Problem 3: A rectangular column with a width of 3 in. and a depth of 6 in. is pinned at both ends and has a length of 20 ft. The column is made of wood with Young's modulus of 10,000 ksi. The column carries an axial compressive force P. a. Determine the critical load to buckle the column. b. If the yield stress is 6 ksi, is the column more likely to buckle or fail by yielding?
The cross section of a concrete corner column that is loaded uniformly in compression is shown in the figure. A circular pipe chase cut-outof 10 i n. in diameter r tins t he height of t he co \u m n (see figure).(a) Determine the average compression stress crr in the concrete if the load is equal to 3500 kips.(b) Determine the coordinates x and y{of the point where the resultant load must act in order to produce uniform normal stress in the column.
14.) Determine the cracking moment (kn-m) of the given beam. Concrete is normal weight with =1.0 and fc' = 28 MPa. Express your answer in 2 decimal places. Use As = 3 - 36 mm.
The cross section shown is for the fixed support of a propped beam that carries an allowable ultimate moment of 60 kN-m. The concrete is lightweight consisting of a lightweight coarse aggregate and a mixture of a lightweight and normal weight fine aggregate. The total volume of fine aggregate is 15 m3 and 7m3 of it are lightweight. Determine the following if the compressive strength of the concrete is 25 MPa, fy=420 MPa and the weight of the concrete is 1600 kg/m3: (a) Cracking Moment (b) Transformed Moment of Inertia. (c) Tension Stress of Concrete. (d) Transformed Compression Steel Stress. (e) Actual Tension Steel Stress. (f) Compression Force in the Concrete due to bending. (g) Total Tension Force of the reinforced concrete due to bending. 90 mm 20 mm 190 mm 70 mm 40 mm 3- Ø25 390 mm 40 mm 4- 020 70 mm 130 mm90 mm'
Please answer
A reinforced concrete beam has a width of 300mm and an effective depth of 580mm. It is reinforced for tension only with 5-32mm diameter bars. Material strength are f'c= 24 MPa and fs = 130 MPa. Assume n=9. Use working stress design. Show complete solution and neat handwriting. 1) which of the following most nearly gives the location of the neutral axis from the extreme compression concrete? a. 272.42 mm b. 288.83 mm c. 256.77 mm d. 189.07 mm 2) which of the following most nearly gives the moment capacity of the beam? a. 255.73 KN.m b. 215.89 KN.m c. 238.16 KN.m d. 226.23 KN.m 3) which of the following is the condition of the beam? a. Over reinforced b. Under reinforced c. Balance condition d. Cannot Determin
SHOW COMPLETE SOLUTION AND ILLUSTRATION
The concrete column is reinforced using four steelreinforcing rods, each having a diameter of 25 mm.Determine the stress in the concrete and the steel if thecolumn is subjected to an axialload of 1200 kN. Est = 200 GPa,Ec = 25 GPa.