A 3-phase, 765 kV, 60Hz, 500 km completely transposed overhead transmission line (OHTL) has the following impedance and admittance: • z = 0.25/30° 2/km 4 × 106/90° S/km • Y = Find the following: 1. The propagation constant. (1 pt) 2. The surge impedance. (1 pt) 3. The load power (in MW) that must be connected to the receiving-end of the line in order to get a receiving-end voltage equal to the sending-end voltage. (1 pt) 4. The ABCD parameters. (4.5 pts)

A 3-phase, 765 kV, 60Hz, 500 km completely transposed overhead transmission line (OHTL) has the following impedance and admittance: • z = 0.25/30° 2/km 4 × 106/90° S/km • Y = Find the following: 1. The propagation constant. (1 pt) 2. The surge impedance. (1 pt) 3. The load power (in MW) that must be connected to the receiving-end of the line in order to get a receiving-end voltage equal to the sending-end voltage. (1 pt) 4. The ABCD parameters. (4.5 pts)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.10MCQ: Transmission line conductance is usually neglected in power system studies. True False

See similar textbooks

Similar questions

Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
1) A 60-Hz, ...-km, three-phase overhead transmission line has a series impedance z = 0.8431L79.04 ohm/km and a shunt admittance y = 5.105 × 106 L90 S/km. The load at the receiving end is 125 MW at unity power factor and at 215 KVLL. Determine the voltage, current, real and reactive power at the sending end and the percent voltage regulation of the line for nominal pi network. (Please determine the length of the transmission line within the specified limits: 150-220 km. By considering the length value you determined yourself, solve the question.)
High voltage engineering subject
A 220 kV, three phase transmission line is 50 km long. The resistance per phase is r 2 per km and the inductance per phase is L mH per km. The shunt capacitance is negligible. If the line supplies a three-phase load of 229 MVA at 0.8 power factor lagging at 220 kV with an efficiency of 97.13% and a voltage regulation of 4.7581%. Use the short line model to find the line resistance and inductance of the line.
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
A 345-kV transmission line has a series impedance of (4 + j60) Q and a shunt admittance of j2 x 10-3 S. Using 100 MVA and the line voltage as base values, calculate the per-unit impedance and per-unit admittance of the line.
A 230-kV, three-phase transmission line has a per phase series impedance of .... (please see attached image).
A 3 phase 13-KV transmission line delivers 8 MVA of load. The per phase impedance of the line is (0.01 + j 0.05 ) p.u. referred to a 13 – KV, 8 – MVA base. What is the voltage drop across the line?
4. A transformer is rated 1000 MVA, 13.8 kV/345 kV with Z=j0.10 pu. If the system base MVA is 500, the corresponding pu impedance becomes (a) j0.10/2 pu (b) j0.10/4 pu (c) j0.10*2 pu (d) j0.10*4 pu 5. Ia, Ib and I, are the three current phasors of a load. For a balanced-load condition, which relation is valid? (a) IF - (Ib + I.) (c) la + I = 1. (d) Ia - I = I. (b) la = I, = Ie
Please answer this diligently. Other answers in the internet seems wrong. Please help me understand and solve this problem. I'll give a like. Thanks!
A short single phase transmission line has a loop impedance of (0.2+j1.2) ohm. At what leading power factor the voltage regulation will be zero ?