A (3 m x 8 m) footing is designed for a multistory building; the footing is constructed at a depth of 3m below the ground surface; the foundation is subjected to a stress of 110 kN/m Bedrock layer is located at 35 m below G.S. saturated and dry unit weight of the soil is 21 kN/m3 and 17 kN/m3 respectively.

A (3 m x 8 m) footing is designed for a multistory building; the footing is constructed at a depth of 3m below the ground surface; the foundation is subjected to a stress of 110 kN/m Bedrock layer is located at 35 m below G.S. saturated and dry unit weight of the soil is 21 kN/m3 and 17 kN/m3 respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Subject:( Geotechnical and foundation engineering )
b) A 3.X m x 3.X m square foundation is to be founded at a depth of 1.5 m below ground level in medium-dense sand with a bulk unit weight of 19 kN/m³ and a saturated unit weight of 20.X kN/m³. The water table is located 3.6m below ground level. The immediate settlement is to be limited to 25mm. Estimate the allowable load on the foundation using the standard penetration test data presented in Table 3 below and applying the appropriate correction factors. Table 3: SPT results Depth 1.5 3.0 3.8 4.6 5.4 6.4 (m) SPT 7 12 12 18 20 25 'N' X=2 2.2 9
A 1.2 meter wide long (strip) footing carries a wall loading of 48 kN per meter of wall length. What vertical stress increase results below the center of the footing at depths of 1 meter, 2 meter, and 4 meter, assuming: (a) Boussinesq conditions apply.(b) Westergaard conditions apply. (c) Show all work
A square footing 5 ft by 5 ft supported on a sandy stratum is designed to carry a column loading of 250,000 lb. The unit weight of the sands underlying the footing location vary between 120 and 125 pcf. Estimate the foundation settlement to be expected using the subgrade reaction method. (Neglect the weight of the footing.)
Problem #4 At a development site in Cebu, City, a plate-load test was conducted on soil whose properties resemble that of sand. The plate used in this PLT is 62 cm square. The ultimate load per unit are (qu) for the test was found to be 620 kN/m2. What should be the maximum allowable load of a 2.5 m square footing? Use a factor of safety of 3. Answer in N.
Q.1. A rectangular footing 2.0 m by 3.0 m is built in a homogeneous bed of sand of having bulk unit weight 20 kN/m³ and saturated unit weight 21 kN/m³ with an angle of shearing resistance of ( 37 P. The depth of the base of footing is 1.8 m below the ground surface and water table is located at a deth of 1.0m below the base of the foundation. a) Justify the adequacy of the footing if the proposed design load on the foundation is 1500 kN. b) depth 1.0 m below the ground Level. Calculate the safe load can be carried by the footing if the water table is located at a Consider the factor of safety of 3. Use Terzaghi's Analysis.
A new residence has a column load of 24000 kN. This is supported via a 3m by 4m rectangular footing whose bottom is 1m below the surface of this homogenous lateritic soil layer. 5m below the footing, there is a 6m thick clay layer. The clay layer has a unit weight of 18.0 kN/m³, void ratio (e) of 0.67, and compressibility index (Cc) of 0.237. The lateritic soil has a unit rate of 19 kN/m³ Find the vertical stress increment at the depth of Sm below the centre and corner of the loaded area.
Calculate the intensity of stress below the centre of footing at depth of 8m due to load of 2000 KN/m² over the footing area of 5 mx 5 m. (Consider 2V: 1H Spread)
A2
2. A 2m X 2m footing carrying 1400KN load is constructed in a site with 2.5m thick clay layer under a 2.5m thick sand layer. If the footing and the ground water table are located at 1.5m below the surface, calculate the consolidation settlement of the footing. You may assume the following soil properties: for sand sat 15.7kN/m°, and for clay eo= 0.65, Cc = 0.25, Cs = 0.06, O'p = 200kN/m² and sat =19.25KN/m³. 19.25kN/m and t = %3D
Need help solving this problem, thanks again