· A 3-m long steel rod has a strain of 1.33 x 10³ m/m when subjected to an axial tensile load of 50 kN. If the steel rod is 20 mm in diameter, determine (a) the modulus of elasticity in GPa, and (b) the deformation in mm.

· A 3-m long steel rod has a strain of 1.33 x 10³ m/m when subjected to an axial tensile load of 50 kN. If the steel rod is 20 mm in diameter, determine (a) the modulus of elasticity in GPa, and (b) the deformation in mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A steel bar of 50 mm × 50 mm square cross-section is subjected to an axial compressive load 200 kN.…

A: Steel bar 50 mm x 50 mm, Axial compressive load P = 200 kN Length L = 2 m, E=160 GPa Deformation = ?

Q: Find the value of strain if stress is 40 N/mm2 and Youngs modulus is 70 N/mm2

A: Given data : The value of stress σ=40 N/mm2 The value of Youngs modulus E=70 N/mm2 Required :…

Q: extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 540 mm.…

Q: 1.17 Figure P1.17 shows the stress-strain relations of metals A and B during tension tests until…

A: Any pressure of a solid object creates a stretched internal stress, similar to the spring-turning…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm.…

A: FIND NA :y=36×95(952)-22×22(95-7-222)36×95-22×22y=22.637mmFIND MOI…

Q: For a given steel cube section subjected to three dimensional state of principal stress. 75 N/mm ☆J…

A: For steel cube,Yield stress=250N/mm2To find the factor of safety according to maximum strain energy…

Q: A steel plate is bent into a circular arc of radius 10 m. If the plate section be 120 mm wide and 20…

A: Given: E=2×105 Nmm2. Arc radius, R = 10 m. Area, A=120 mm×20 mm. y = 10 mm.

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 880 mm.…

Question

5. A 3-m long steel rod has a strain of 1.33 x 10-3 m/m when subjected to an axial tensile load of 50 kN. If
the steel rod is 20 mm in diameter, determine (a) the modulus of elasticity in GPa, and (b) the deformation
in mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 19N/mm2, find the maximum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm2. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Txy 10 N/mm2
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b₁ = 33 mm, d₁ = 109 mm, b₂ = 20 mm, d₂ = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 11 MPa. Determine the largest moment M that can be applied as shown to the beam. b₂ a M B A Answer: M = L d₂ N•m b₁ d₁
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 580 mm. The cross-sectional dimensions of the beam are b1 = 36 mm, d1 = 106 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 20 MPa, and the allowable compressive bending stress is 9 MPa. Determine the largest moment M that can be applied as shown to the beam.
The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine: The stress of aluminum in segment AC. Answ: 63.66 MPa The stress of aluminum in segment CD. Answ: 13.93 MPa The stress in steel in segment CD. Answ: 39.79 MPa The total deformation of the bar. Answ: 0.29273 mm
4.20 A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the magnitude of the load required to produce a 10 in. change in diameter if the deformation is entirely elastic. Assume a Young's modulus of 11 X 106 psi and a Poisson's ratio of 0.33.
Help me
A cylindrical bar of steel 9.9 mm (0.3898 in.) in diameter is to be deformed elastically by application of a force along the bar axis. Determine the force that will produce an elastic reduction of 3.0×10-3 mm (1.181 ×10-4 in.) in the diameter. For steel, values for the elastic modulus (E) and Poisson's ratio (v) are, respectively, 207 GPa and 0.30. i N
The following shaft is composed of two materials, both rigidly bonded. The data is provided in the table: Determine: The maximum torque that can be applied based on the maximum stresses of each material. The total deformation of the shaft with the torque from the previous section. The maximum torque that can be applied if the maximum deformation of the shaft is 2.50 rad.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 110 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam.
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 580 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 112 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a a M d2 A B bị