A 2300 V, 400 HP, 50 Hz, eight-pole, 0.85 Leading PF, Y-connected synchronous motor is having a negligible armature resistance, and a synchronous reactance of 10 Q. This motor is operating at EA = 2041 Volts, and & = -25°. If the flux is increased by 15 % while the power is kept constant, find the new armature current and the new power factor of the motor.

A 2300 V, 400 HP, 50 Hz, eight-pole, 0.85 Leading PF, Y-connected synchronous motor is having a negligible armature resistance, and a synchronous reactance of 10 Q. This motor is operating at EA = 2041 Volts, and & = -25°. If the flux is increased by 15 % while the power is kept constant, find the new armature current and the new power factor of the motor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: a dc shunt motor runs at 900 r.p.m from a 460 V supply when taking an armature current of 25 A.…

A: Take the ratio of back emfs to find the speed at terminal voltage of 230 volts. Back emf is directly…

Q: A 4 pole DC shunt generator with 800 duplex wave connected armature conductors supplies a load of…

Q: An 8 pole DC shunt generator with 900 wave-connected armature conductors supplies 10ohm at 500 V…

A: To find the answers, we can use the following formulas and calculations:1.1 The flux per pole:The…

Q: 3. A 4 pole, 250 dc shunt motor has a lap connected armature with 960 conductors. The flux per pole…

A: The solution can be achieved as follows.

Q: A 250-V shunt motor runs at 1000 rpm, at no-load and takes 8A. The total armature and shunt field…

A: We have an shunt motor which is running we have been asked to find the speed when loaded and taking…

Q: With the aid of a diagram as shown, explain how does AC generator work and describe the operating…

A: AC generator working: As per Faraday's law of electromagnetic induction, an EMF is induced in the…

Q: Suppose that we are designing a 1200-rpm dc motor to run from a 240-V source. We have determined…

A: Given Nm=1200 rpm Calculating linear velocity of the conductor Nm=ωm602πωm=Nm602πωm=12002π60ωm=40π

Concept explainers

Motor Load, Torque, and Power Quality Requirement

An electric motor is a gadget that changes electrical energy into mechanical energy over to follow up on a mechanical burden. The weight set on the motor because of this mechanical movement is known as motor load. Appropriately matching the motor burden to the engine is vital to forestall harm to the engine or wasteful and unnecessary expensive activity. Engines perform such undertakings as moving a thing starting with one spot then onto the next, cutting it, changing its shape, etc. The motors might be evaluated as far as a few variables including power yield, voltage, current, and temperature. Harm to an engine might happen when it is worked under over the top engine load contrasted with its appraised limit.

Question

A 2300 V, 400 HP, 50 Hz, eight-pole, 0.85 Leading PF, Y-connected synchronous motor is having a negligible armature resistance, and a
synchronous reactance of 10 0.
This motor is operating at EA = 2041 Volts, and & = -25°.
If the flux is increased by 15 % while the power is kept constant, find the new armature current and the new power factor of the motor.
Select one:
O a. lA = 121.4 Amp, and PF = 0.71 Lagging
O b. None
O c. lA = 121.4 Amp, and PF = 0.71 Leading
O d. la = 94.21 Amp, and PF = 0.79 Leading
O e. lA = 94.21 Amp, and PF = 0.79 Lagging
Clear my choice

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 10 kW, 250 V Shunt motor has an armature resistance of 0.5 ohm and a field resistance of 200 ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full load and rated voltage, the line current is 47 A and because of armature reaction, the flux is 4 % less than it no load value. a.) What is the full load speed? b.) What is the developed torque at full load?
A 240-volt series motor has an armature resistance of 0.42 ohm and a series-field resistance of 0.18 ohm. If the speed is 500 rpm when the current is 36 A, what will be the motor speed when the load reduces the line current to 21 A? (Assume a 3-volt brush drop and that of the flux is proportional to the current.). Ans.: 1435 rpm show diagram and step by step process
An 8 pole DC shunt generator with 900 wave-connected armature conductors supplies 10ohm at 500 V when driven at 500 rpm. The armature resistance 0.4ohm and the field resistance is 250ohm . Determine: . . 2 1.1 The flux per pole 2.1.2 The armature current for maximum efficiency if the rotational losses are 10% of the ar- mature copper losses . 3.2 A series motor runs at 600 rpm while drawing 40-A from 600-V supply. The total re- sistance of the armature and the field is 0.5-ohm. Determine the value of the additional re- sistance required in series with armature to reduce the speed to 450 rpm if the load toque is: 3.2.1 Constant 3.2.2 Proportional to the square of the speed .
The schematic and torque-speed characteristics of a series wound DC motor are shown below : Field winding DC Supply Eb speed Torque - T-K, I, Field Flux = ø = Kla (i) According to the equations given above, explain why the torque of the series-wound DC motor is so high at low speed. Give application examples that require such torque-speed characteristics. A series-wound DC motor should never be started with light or NO LOAD. Give reason. (ii) (iii) Armature anbio
A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with rotating speed of 1000rpm. The armature is wave-wound and has 500 conductors. The useful flux per pole is 0.03Wb and there are 4 poles (2 pairs of poles). The armature resistance is 0.4 Ohms. Calculate: 1.The internal emf of the motor. 2.The armature current. CLEAR AND CORRECT OR DISLIKE
Draw the circuit please.
Consider a shunt DC motor with an armature resistance RA=0.2 ohm and terminal voltage VT = 160 V. The motor rated speed is 1800 RPM. The total field resistance 240 ohm. Assume No armature reaction in this machine. The variation of the armature terminal voltage as a function of the field current is measured under no-load conditions and shown below:
A lap-wound, 6-pole dc motor has 180 conductors distributed on the armature’ssurface. If the armature current is 25 A and the flux per pole is0.5 Wb, determine the torque developed by the machine. When the motoris operating at 900 rpm, what is the back emf? What is the current in eachconductor?
QUESTION 2 a) Draw the equivalent circuit and torque-speed characteristic curve for a series DC motor. b) Briefly explain the induced torque occurs in a series DC motor. e) A 20-hp 240-V 76-A 900 rimin series motor has a field winding of 33 turns per pole. Its armature resistance is 0.09 2, and its field resistance is 0.06 2. The magnetization curve expressed in terms of magnetomotive force versus Ex at 900 rimin is given by the following table: Table Q2 c): The magnetomotive force table for a de motor taken at 900r'min E. V 95 150 188 212 229 243 F.A tuus 1000 1500 2000 2500 500 3000 If the motor running at 33 percent of the full-koad armature current, determine: ) The motor's power converted from electrical to mechanical form, Prene i) The motor's torque, Tnit ii) The motor's speed, n
A 900 rpm, 4 pole lap wound shunt motor takes 300 A. The flux per pole is 0.02 Wb and the armature has 1500 conductors. The shunt field takes 4 A of current. Solve for back emf (V).
Consider a separately-excited DC motor with an armature resistance RA = 0.2 ohm and terminal voltage VT = 130 V. The motor rated speed is 1200 RPM. The field winding supply VF= 36 V and the field resistance is adjustable. The motor has compensating windings and interpoles.
show circuit diagram and step by step solution plz