A 230 V, 980 RPM, 195 A separately excited dc motor has an armature resistance of 0.025 2. The motor is operated in dynamic braking with chopper control. A braking resistance of 1.9 2. Calculate the duty ratio of the chopper for a motor speed of 580 RPM and braking torque equal to the rated value.

A 230 V, 980 RPM, 195 A separately excited dc motor has an armature resistance of 0.025 2. The motor is operated in dynamic braking with chopper control. A braking resistance of 1.9 2. Calculate the duty ratio of the chopper for a motor speed of 580 RPM and braking torque equal to the rated value.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 180V DC shunt motor drives a constant torque load at speed of 1600 rev/min the armature and field resistance are 2ohm and 100ohm reepesctively the motor draws a line current of 8.7A. Assume that a resistance is added in the field circuit to reduce the currentby 100%. Calculate the value of the added resistance and the extra field losses
• A 120-V shunt motor has R₁ = 0.25 0 and Rfw = 80 2. The motor takes 4 A at a no-load speed of 1500 rpm. If the motor is to develop a torque of 20 N-m at a speed of 2000 rpm, determine the external resistance that must be added in series with the field winding. (352) • If the rotational loss is proportional to the speed, determine the efficiency and the horsepower rating of the motor at 2000 rpm.
Armature resistance of a 230V shunt motor is 0.6 0 and no load current is 5A. When the rotor is loaded it is taking armature current of 60A. The speed is 1200rpm.Estimate the noload speed of a motor. a. 1513.12 rpm b. 1500 rpm O c. 1400 rpm O d. 1404.12 rpm
In the series motor, the armature resistance is 0.1Ohm and the field resistance is 0.15Ohm and it is taking 50A of the current aand the valeu of the supply voltage is 230V and value of the rpm is 720 rpm. The loses present in the circuit as core and the friction is 650W. Neglect all other losses. Determine the value of the output power.
A 200 V dc shunt motor takes a current of 20A on a certain load. R= 12 and Rah= 2002. Find the resistance to be inserted in series with the armature to reduce the speed to 75% of its original value if the load torque is constant.
Q16 A 240V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the slip is 6% the motor constants referred to the stator are : Stator resistance 2.20; rotor resistance 3.80 Stator reactance = 30 ; rotor reactance 2.10 Magnetizing reactance 860 ; iron and friction loss 500 Draw the equivalent circuit and from it find the output power and efficiency at the given loading. Ans[ 1090 W, 74.6%]
Can you solve the question step by step with clear writing ?
Please answer alll subparts in short for like either dislike
electromechanical energy conversion question. please answer it clearly.
45) A 40hp, 440V, four pole dc motor has an armature wave-wound with 846 conductors and the commutator has 141 segments. The full load efficiency is 85% and the shunt current is 1.25A. If the brushes are shifted backward through segments from the geometric neutral axis, calculate (a) The demagnetizing ampere-turns per pole (b) The distorting ampere-turns per pole on full load.
The following figure shows the circuit of a DC drive system. Choose the right expression concerning this system. Forward bridge Reverse bridge L1 L1 L2 L3 23 Armature Shunt field L3 23 L2 O a. This drive is a Regenerative DC drive. It allows controlling the motor speed ONLY below its base speed. Changing the rotation direction requires to feed the motor from the reverse bridge. The reverse bridge is also used while braking to transform the excess energy into AC and feed it to grid lines O b. This drive is a Non-regenerative DC drive. It allows controlling the motor speed below and above its base speed. Changing the rotation direction requires external contactors to be connected. The reverse bridge is used while braking to direct the excess energy to braking resistor bank Oc. None of the choices Od. This drive is a Regenerative DC drive. It allows controlling the motor speed below and above its base speed. Changing the rotation direction requires to change the pulses fed into the…