A 200-V, 100 A armature full-load line current, 1200 RPM, shunt DC motor is consideredin this problem. Its characteristics are given below:ofRA = 0.20 2RF = 150 2NF=2000 turnsThis motor has compensating windings and interpoles.The magnetization curve for this motor at 1200RPM is shown in a tabular form below:0.1 0.2 0.4 0.50.6 0.81.0 1.2 1.6| 1.8 2.02.2 2.4If, AEA,V 6.0 25110 135 160 205 235 255 275 285 288 290 29150For Radj between 502 and 450 2 , find the range of this motor if the armature currentL= 66 Amperes.Select one:O a. Range of speed between 818 RPM and 1620 RPMO b. Range of speed between 880 RPM and 2038 RPMO c. NoneO d. Range of speed between 900 RPM and 1820 RPM

The range of speed for the given details is calculated as shown below

A 200-V, 100 A armature full-load line current, 1200 RPM, shunt DC motor is considered in this problem. Its characteristics are given below: RA = 0.20 2 RF= 150 2 NF=2000 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1200RPM is shown in a tabular form below 0.1 0.2 0.4 0.5 0.6 0.8 1.2 1.6 1.8 2.0 2.2 2.4 If. A EA.V 6.0 25 50 1.0 110 135 160 205 235 255 275 285 288 290 291 For Radj between 502 and 450 2 , find the range of this motor if the armature current I= 66 Amperes.

A 200-V, 100 A armature full-load line current, 1200 RPM, shunt DC motor is considered in this problem. Its characteristics are given below: RA = 0.20 2 RF= 150 2 NF=2000 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1200RPM is shown in a tabular form below 0.1 0.2 0.4 0.5 0.6 0.8 1.2 1.6 1.8 2.0 2.2 2.4 If. A EA.V 6.0 25 50 1.0 110 135 160 205 235 255 275 285 288 290 291 For Radj between 502 and 450 2 , find the range of this motor if the armature current I= 66 Amperes.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A A permanent magnet DC motor has an armature resistance supplied by a 75-V DC Source, 1.4 S2. When it n svy t no-load speed d 2200 pm and draws 1.7 A. a) what 6.) What is the rotational'loss ? TS the output power (in hp) when it is operated at from 1800 rpm a 70-V DC source 7
the BLDC motors have the advantage of High Efficiency Compactness Low Maintenance All of the answers When the speed of the DC motor is Increases its Armature current Remain Constant Decreases Increases Any of the answers A variable reluctance stepper motor is constructed of .. . material with salient poles. ferromagnetic paramagnetic non-magnetic diamagnetic
Draw the circuit please.
ses This course A 200-V, 100 A armature full-load line current, 1800 RPM, shunt DC motor is considered in this problem. Its characteristics are given below: RA = 0.20 2 RF= 150 2 %3D NF 2000 turns %D %3D This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below. If,A 0. 0.1 0.2 0.4 0.5 0.6 0.8 1.8 2.0 160 205 235 255 275 285 288 1.0 1.2 1.6 2.2 2.4 EA,V 6.0 25 50 110 135 290 291 For Radj between 502 and 450 2 , find the range of this motor if the armature current L= 66 Amperes. Select one: a. None b. Range of speed between 1319 RPM and 3057 RPM C. Range of speed between 1818 RPM and 3220 RPM O d. Range of speed between 1222 RPM and 2860 RPM
A 200 V D.C. shunt motor takes 20 A at rated voltage and runs at 1000 r.p.m. Itsarmature resistance is 0.1 ohm. Calculate the value of additional resistance requiredin the armature circuit to reduced the speed to 800 r.p.m when the load torque isindependent of the speed.Ignore the field current. (Ans.1.98 ohm)
Q1 Describe the Characteristics, characteristics, efficiency calculations, their applications Of DC Motors in detail
A hybrid stepper motor has four stator poles and two 5-pole permanent magnet armatures, as shown in Figure Q3. A1 armature 1 armalure 2 A2 Figure Q3 Describe how the motor can be excited by a two-phase source to rotate in the counterclockwise direction.
I need the answer as soon as possible
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
A 200-V, 100 A armature full-load line current, 1800 RPM. hunt DC motor is considered in this problem. Its characteristics are given below: RA=0.20 52 RE 50 $2 NF-2000 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below If.A 0 0.1 0.2 0.4 0.5 0.6 0.8 1.0 1.2 1.6 1.8 2.0 2.2 2.4 EA-V 6.0 25 50 110 135 160 205 235 255 275 285 288 290 291 For Rad between 50 52 and 450 2. find the range of no-load speed of this motor. Answer: No-load Speed Range from RPM to RPM.
A 3-phase, 48 kW, start-connected permanent magnet (PM) motor has a rated speed of 6600 rpm when supplied from a 110 Hz supply. The d-axis and q-axis inductances are La= 3.5mH and Lg= 4.7mH, respectively. The armature resistance and rotational losses are negligible. The motor operates without field weakening up to 6600 rpm, and a negative direct-axis current is imposed if the motor operates at speeds above 6600 rpm. The no-load terminal line-to-line voltage at 5000 rpm is 420 V (RMS). a. Determine the permanent magnet flux linkage. b. Calculate the rated phase current. c. Calculate the rated line to line voltage of the PM motor. с. d. At a speed of 7300 rpm, the PM motor operates in field weakening mode with a direct axis current of -30A and produces a torque of 30 Nm. Determine the per-phase current at this operating condition.
Consider a separately-excited DC motor with an armature resistance RA = 0.2 N and terminal voltage VT = 130 V. The motor rated speed is 1000 RPM. The field winding supply VF= 24 V and the field resistance is adjustable. The motor has compensating windings and interpoles. 0.3 IF (A) EA (V) 0.0 0.1 0.2 0.4 0.5 0.6 0.7 0.8 30 102 These values were taken at speed n= 1000 RPM 60 85 115 124 130 134 If the motor is driving a load at rated armature current IA = 60 A, with Radi +RF = 40 2. Find the speed of rotation ofthe motor in RPM.Select one: a. Speed n = 952 RPM b. None c. Speed n = 1051 RPM d. Speed n = 1000 RPM