sesThis courseA 200-V, 100 A armature full-load line current, 1800 RPM, shunt DC motor is consideredin this problem. Its characteristics are given below:RA = 0.20 2RF= 150 2%3DNF 2000 turns%D%3DThis motor has compensating windings and interpoles.The magnetization curve for this motor at 1800 RPM is shown in a tabular form below.If,A0.0.1 0.2 0.40.50.60.81.8 2.0160 205 235 255 275 285 2881.01.21.62.22.4EA,V 6.0 2550110135290 291For Radj between 502 and 450 2 , find the range of this motor if the armature currentL= 66 Amperes.Select one:a. Noneb. Range of speed between 1319 RPM and 3057 RPMC. Range of speed between 1818 RPM and 3220 RPMO d. Range of speed between 1222 RPM and 2860 RPM

In this question we need to find range of motor speed at given condition.

ses This course A 200-V, 100 A armature full-load line current, 1800 RPM, shunt DC motor is considered in this problem. Its characteristics are given below: RA = 0.20 2 RF= 150 2 %3D NF 2000 turns %3D %3D This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below: 0. 0.1 0.2 0.4 If,A EA,V 6.0 25 0.5 0.6 0.8 1.8 2.0 160 205 235 255 275 285 288 1.0 1.2 1.6 2.2 2.4 50 110 135 290 291 For Radj between 502 and 450 2 , find the range of this motor if the armature current L= 66 Amperes. Select one: a. None b. Range of speed between 1319 RPM and 3057 RPM C. Range of speed between 1818 RPM and 3220 RPM O d. Range of speed between 1222 RPM and 2860 RPM

ses This course A 200-V, 100 A armature full-load line current, 1800 RPM, shunt DC motor is considered in this problem. Its characteristics are given below: RA = 0.20 2 RF= 150 2 %3D NF 2000 turns %3D %3D This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below: 0. 0.1 0.2 0.4 If,A EA,V 6.0 25 0.5 0.6 0.8 1.8 2.0 160 205 235 255 275 285 288 1.0 1.2 1.6 2.2 2.4 50 110 135 290 291 For Radj between 502 and 450 2 , find the range of this motor if the armature current L= 66 Amperes. Select one: a. None b. Range of speed between 1319 RPM and 3057 RPM C. Range of speed between 1818 RPM and 3220 RPM O d. Range of speed between 1222 RPM and 2860 RPM

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(c) What are the principle characteristics of DC series motor and DC compound motor, and what are its uses?
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 3 ALoad torque=Tload= 8 Nma) 143 rpmb) 734 rpmc) 1361 rpm d) 77 rpm e) 1333 rpm
Induct.motor.
I need the answer as soon as possible
The relation between armature torque and armature current of a DC motor is Parabolic Linear Inverse Exponential
3. A 4 pole, 250 dc shunt motor has a lap connected armature with 960 conductors. The flux per pole is 2 x 102Wb. Calculate the torque developed by the armature and the useful torque in N-m when the current taken by the motor is 30A. The armature resistance is 0.12 ohm and the field resistance is 125ohm. The rotational losses amount to 825W
what are the disadvantages of slip ring induction motor?
Q4) What is the effect in series motor if you assume V = Eb , with low resistance fielding winding ? a) b) The given information about series motor on full – load (with that the flux is proportional to the field current) is a ) takes ( 78A) and runs at (850 r.p.m) , the series winding resistance is (0.04 2) , with diverter in parallel with the field winding is a (0.18 2) and the armature resistance is (0.09 S2). ( 220 V Neglected the iron, friction and windage losses. Determine the efficiency , speed when developing full load torque ,the maximum efficiency .
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...
A 3 phase, 1500 rpm, 2200 V, star connected synchronous motor has an impedance of 0.4+j90 per phase. At some excitation 2900 V is induced in the armature. Find the maximum torque developed by motor before the motor breaks out of synchronism. Also find the load angle this time.