A 20-mm diameter steel rod, 250 mm long is subjected to a tensile force of 75 kN. If the Poisson’s ratio μ is 0.30, determine the lateral strain of the rod. Use E = 200 GPa. Ans; Ey= -3.581x10^-4mm/mm

A 20-mm diameter steel rod, 250 mm long is subjected to a tensile force of 75 kN. If the Poisson’s ratio μ is 0.30, determine the lateral strain of the rod. Use E = 200 GPa. Ans; Ey= -3.581x10^-4mm/mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Related questions

Q: The state of plane strain on an element has components of Ez = 500 (10-6), y = 300(10-6), and…

Q: A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight…

A: The cross sectional area of wire is The modulus of elasticity is The yield strength is The…

Q: A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the…

A: (a) To Find : The normal strain in rod 1. Given : The length of rod 1 is L1=148 in The length of…

Q: Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and…

A: Given that, Esteel=20×1010PaEbrass=10×1010Pa

Q: The stress strain curve determined from a sample of material is shown in the figure. The original…

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

Q: A solid steel rod is connected to an arm loaded by to forces, F-1 kN and F₂ -1.2 KN. A three-element…

A: Given Data: F1=1 kNF2=1.2 kNεa=60 μεεb=135 μεεc=264 μεθ1=0oθ2=60oθ3=120o To Find: The linear strain…

Q: A strain gage is mounted to the outer surface of a thin-walled boiler. The boiler has an inside…

Q: A material is subjected to a pressure of 5 MPa. If the material has an elastic modulus of 80 GPa and…

Q: is shown below, 400 300 200 100 Stress (MPa)

A: 1.Modulus of elasticity can be obtained by taking the slope of stress-strain curve in elstic…

Q: After load P is applied to the pin-connected structure, a normal strain of = +650 μe is measured in…

Q: The rigid beam is supported by a pin at A and wires BD and CE. Figure 3 m 2m 1 of 1 4 m ▾ Part A If…

A: Given data Downward displacement of C = 8mm Find the normal strain in CE and BD

Q: The state of strain at the point on the pin leaf has components of € = 200(10-6) Ey 180(106), and…

Q: (a) the strain in the cable at a depth of 700 ft. (b) the total elongation of the cable.

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

Question

A 20-mm diameter steel rod, 250 mm long is subjected to a tensile force of 75 kN. If the Poisson’s ratio μ is 0.30, determine the lateral strain of the rod. Use E = 200 GPa.

Ans; Ey= -3.581x10^-4mm/mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a) Determine the strains for an element oriented at an angle = 250. (b) Find the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 30°. (b) Determine the principal strains of the clement. Confirm the solution using Mohr’s circle for plane strain.
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E wherey= 2.2 lb/in.³ is the specific weight of the material, y = 5.0 in. is the distance from the free (i.e., bottom) end of the bar, L = 25 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length of the bar (c) the maximum normal strain in the bar. Answer: (a) ō = i (b) Eave = i (c) Emax = i x10-in. με με
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y=2.4 lb/in.³ is the specific weight of the material, y = 0.6 in. is the distance from the free (i.e., bottom) end of the bar, L = 6 in. is the length of the bar, and E=30000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) 5 = 1 (b) Sa (c) Emax= i x10-6 in. με με
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.8 lb/in.3 is the specific weight of the material, y = 2.0 in. is the distance from the free (i.e., bottom) end of the bar, L = 20 in. is the length of the bar, and E= 29000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar. Part 1 Your answer is correct. Calculate the change in length of the bar due to its own weight. Answer: 6 = 6.436 eTextbook and Media Part 2 * Your answer is incorrect. Calculate the average normal strain over the length of the bar. Answer: Eavi 3.22 x10-6 in. eTextbook and Media Save for Later με Attempts: 1 of 5 used Attempts: 2 of 5 used Part 3 The parts of this question must be completed in order. This part will be available when you complete the part above. Submit Answer
Determine the change in length, width and thickness of steel bar which is 4m long, 30mm wide and 20mm thick and is subjected to an axial pull of 30 kN in the direction of length. Take E = 200 GPa and poison's ratio of 0.3. Also determine the volumetric strain and change in volume.
A 45° strain rosette was placed on the surface of a critical point on an engineering part. The following were measured: Ea = 400 μ C ли 45° mm mm 45° ли Gauge a was aligned with the x-axis. a. Determine Ex, Ey, Yxy b. Using Mohr's Circle, find the principal strains and the maximum shear strain at that point, and find the orientation of the principal planes from the given x-y axes. y ли & = 450 μ ஆ b a mm X mm & c = 500 μ y+ ос mm mm eb 10₂ X
A tensile stress is to be applied along the long axis of a cylindrical steel rod that has a diameter of 10mm. A change in diameter is produced of 2.5x10^-3 mm when the deformation is entirely elastic. Given: E = 200GPa and v = 0,3. Determine the lateral strain
A thin polymer plate PQR is deformed such that corner Q is displaced downward a distance L = 0.10 in. to new position Q' as shown. Determine the magnitude of the shear strain at Q' associated with the two edges (PQ and QR). P 25 in. 7982 μrad 6862 μrad 09533 μrad O6186 prad O8600 μrad 4 in. R 10 in. L X
For the state of a plane strain with Ex, Ey and yxy components: (a) construct Mohr's circle and (b) determine the equivalent in-plane strains for an element oriented at an angle of 30° clockwise. Ex = 250 x 10-6 Ey = 310 x 10-6 Yxy = -100 × 10-6