A 130-N pull Tis applied to a cord, which is wound securely around the inner hub of the drum. Determine the moment of T about the drum center C. At what angle e should T be applied so that the moment about the contact point Pis zero? The moment is positive if counterclockwise, negative if clockwise. T- 130 N 100 470 Dimensions in mm Answers: N-m Mc=

A 130-N pull Tis applied to a cord, which is wound securely around the inner hub of the drum. Determine the moment of T about the drum center C. At what angle e should T be applied so that the moment about the contact point Pis zero? The moment is positive if counterclockwise, negative if clockwise. T- 130 N 100 470 Dimensions in mm Answers: N-m Mc=

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use the subsne member to make a compieneanlyss of e comples uss shown 25kN d 3m 25KN 4 m e1.5 m 2 at 4 m = 8 m
Note: Don't copy from Chegg. Kindly do it your own way.
The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.753 in. If a force of 15 kip is applied to the bar, determine the angle of tilt of the bar in degrees. 3.5 ft 2.5 ft E D -1.25 ft- 0.75 ft' 1 ft 15 kips
asap
Note:hand written solution should ne avoided.
State the determinacy and the stability.
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. From the frame loaded as shown. Solve the following: a. Reaction at column A.b. Moment at column A.c. Force at member GH.d. Force at member FE.e. Force at memeber FH.
W weight 74N, reaction force on K wheel is one third of w. (1/3). In this case, find the load on the bars HIJ, GL, CL and FC. The rollers are frictionless.
2-2 A 100-N force is applied at end C of the rod as shown. c) Assess the effect of the angle being varied from 0° to 360° to the moment of the 100-N force about point A. [b) (i) MA=0 N-m; (ii) MA=-24k N-m; (iii) MA=-12k N.m] 2-3 A 600-N force is applied on end D of the bent rod as shown. c) Assess the effect of the angle being varied from 0° to 180° to the moment of the 600-N force about point A. [b) (i) MA= 180 N-m; (ii) MA= - 480k N-m; (iii) MA= 180k N-m; (iv) MA=- 432k N.m] Figure IA Figure 150 mm P2-2 600 N 50 cm B P2-3 90 mm 0 000 B 30 cm C 100 N 30 cm
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) A prybar is used to remove a nail as shown. Determine the moment of the 240 N force about the point O of the contact between the prybar and the small support block. (in N-m)
500 mm 500 mm B E A -120 N -300- mm PA D 300 mm 750 mm 200 N C For the frame shown below, calculate: a) the magnitude of the force that the pin at C exerts on the member BDC. b) the magnitudes of the forces that the pin at B exerts on the members BFA and BDC. Assume that the 120 N force is applied to the Pin at B.
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE