A 130-mm-thick oneway slab is reinforced with 12-mm-diameter tension bars spaced at 110 mm on centers. Concrete cover is 20 mm, concrete strength is 21 MPa and steel yield strength fy = 275 MPa. Unit weight of concrete is 23.5 kN/m³. a. What is the ultimate moment capacity of the slab? b. If the slab is simply supported over a span of 4 m, what safe uniform live load pressure can the slab carry?

A 130-mm-thick oneway slab is reinforced with 12-mm-diameter tension bars spaced at 110 mm on centers. Concrete cover is 20 mm, concrete strength is 21 MPa and steel yield strength fy = 275 MPa. Unit weight of concrete is 23.5 kN/m³. a. What is the ultimate moment capacity of the slab? b. If the slab is simply supported over a span of 4 m, what safe uniform live load pressure can the slab carry?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

-10 In prestressed concrete we select one of the following materials strengths: Select one: out of O a. fy = 1725 N/m2, fc= 30 N/m2 question O b. fc: = 50 N/m2, fy = 410 N/m2 O c. fy = 40 N/m2. fc = 1725 N/m2 O d. fc = 40 N/m2. fy= 1100 N/m2
T beams
Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a live load of 30 kN/m. The prestressing force is KN. [Take permissible stresses in concrete and steel as 15 MPa and 1200 MPa respectively]
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. The concrete cover to bar centroid is 80 mm and at the bottom is 70 mm. use concrete strength f'= 21 MPa and steel yield strength fy=415 MPa for all bars. 1. Determine the tensile steel ratio when the beam is in positive bending. a. 0.01567 b. 0.01283 c. 0.01169 d. 0.01923 2. Determine the nominal moment capacity in kN-m of the beam in positive bending. a. 188.30 b.167.70 c.218.96 d.193.68 3. Determine the tensile steel ratio when the beam is in negative bending. a. 0.00406 b. 0.00475 c.0.00383 d. 0.00508 please provide a complete solution so I can understand. Very much appreciated to solve it early !!
Design a one way slab (as shown in fig) for inside of a building. Normal weight aggregate concrete will be used with a density of 145pcf. Compressive strength of concrete = 4000psi Yield strength of steel = 60000psi LL = 250psf
A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
Pre-stressed.
CAN SOMEONE HELP ME SOLVE THIS REINFORCED/PRESTRESSED CONCRETE PROBLEM. USE NSCP 2015 A concrete beam has a width of 304.8 mm and an effective depth of 495.3 mm. It is reinforced with 14.194 cm2 steel bars with fc′ = 17,237.5 kPa (n = 10). Determine the flexural stresses caused by a bending moment of 84.1 kN·m
Help 35 minutes