A 1045 hot-rolled steel tension test specimen has the original diameter and length of 6 mmand 25 mm, respectively. The load and change in length data were recorded as shown inTable 1 below:Table 1. Load and change in lengthLoad (KN)Change in Length Load (KN)Change in Length(mm)(mm)20.562.262.940.0120.723.365.580.0220.613.838.520.0319.974.0011.160.0418.72Fracture.12.630.0513.020.0613.160.0813.220.1016.150.6118.501.0420.271.80Page 163.1) Calculate stress and strain for the data in Table 1. Please show 1 calculation of stressand 1 of strain. The rest you must tabulate.

Given Data d=6mm l=25mm To tabulate stress and strain

Answered: A 1045 hot-rolled steel tension test…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20 mm. During the test the specimen yields under a load of 100,000 N. The corresponding gage length = 50.5 mm. This is the 0.2% yield point. The maximum load of 180,000 N is reached at a gage length = 65 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage length of 73 mm, determine the ductility. i need clear ans by hand and solve very very fast in 20 min and thank you | DYBALA
Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted on a high-strength steel. The test specimen had a diameter of 0.505 inch and a gage length of 2.00 inch. Using software. plot the Stress-Strain Diagram for this steel and determine its: A= TTdT(050s A %3D 1. Proportional Limit, 2. Modulus of Elasticity, 3. Yield Strength (SY) at 0.2% Offset, 4. Ultimate Strength (Su), 5. Percent Elongation in 2.00 inch, 6. Percent Reduction in Area, 7. Present the results (for Steps 1-6) in a highly organized table. e Altac ie sheet (as problelle 4 A = 0.2.002 BEOINNING of the effort Elongation (in) Elongation (In) Load Load #: #3 (Ib) (Ib) 1 0.0170 15 12,300 0.0004 1,500 16 12,200 0.0200 0.0010 3. 3,100 17 12,000 0.0275 0.0016 4,700 18 13,000 0.0335 5. 6,300 0.0022 19 15,000 0.0400 0.0026 6. 8,000 20 16,200 0.055 0.0032 9,500 21 17,500 0.0680 0.0035 8. 11,000 22 18,800 0.1080 0.0041 11,800 23 19,600 0.1515 0.0051 24 20,100 0.2010 10 12,300 0.0071 25…
the material had a tensile stress of 67.7 ksi then was unloaded. the original length of the specimen was 5.0 inches. show the line on the diagram you would expect the material to follow as the load was released. estimate the length of the specimen after all load was removed.
In a tensile test for an aluminum alloy, the sample is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Determine the axial stress of the sample under a tensile load of 9 kips: ____ ksi. Pay attention to units and calculate your answer to 1 decimal place.
3. The elastic portion of the stress-strain diagram for a titanium alloy used for medical implants shown. The specimen from which it was obtained has an original diameter of 10 mm and a gage length of 45 mm. If a tensile load of P = 300 kN is applied to the specimen. Take Poisson ration 0.3. a) determine specimen's new length after deformation. b) determine specimen's new diameter after deformation. Make sure to include the calculation for all steps including E and longitudinal and lateral strains MPa 700 600 500 400 300 200 100 E 10-3 10 15 (Ans:lnew - 46.718mm, Dnew - 9.885mm, ) for tregting

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A 1045 hot-rolled steel tension test specimen has the original diameter and length of 6 mm and 25 mm, respectively. The load and change in length data were recorded as shown in Table 1 below: Table 1. Load and change in length Load (KN) Change in Length Load (KN) Change in Length (mm) (mm)