A 10-hp, 120-V, 1000 rpm shunt DC motor has a full load armature current of 70 A when operating at rated conditions. The armature resistance of the motor, RA is 0.12 Q and the field resistance Rp is 40 Q. The adjustable resistance of the motor in the field circuit, Radi may be varied over the range from 0 to 200 Q and currently set at 100 Q. Armature reaction can be ignored in this machine. The magnetization curve for this motor, taken at a speed of 1000 rpm is summarized in the following table. Note that linear interpolation applies when the value is not explicitly stated in the table. EA, V 78 95 112 118 126 IF, A 0.00 0.80 1.00 1.28 1.44 2.88 If the motor is now unloaded with no changes in terminal voltage or Radj, how much is the increase in the no load speed of the motor? Hint: For linear interpolation in the interval, the formula to obtain the unknown point in this interval is as follows: Yo(x1 - x) + y1(x – x) y = X1 - Xo

A 10-hp, 120-V, 1000 rpm shunt DC motor has a full load armature current of 70 A when operating at rated conditions. The armature resistance of the motor, RA is 0.12 Q and the field resistance Rp is 40 Q. The adjustable resistance of the motor in the field circuit, Radi may be varied over the range from 0 to 200 Q and currently set at 100 Q. Armature reaction can be ignored in this machine. The magnetization curve for this motor, taken at a speed of 1000 rpm is summarized in the following table. Note that linear interpolation applies when the value is not explicitly stated in the table. EA, V 78 95 112 118 126 IF, A 0.00 0.80 1.00 1.28 1.44 2.88 If the motor is now unloaded with no changes in terminal voltage or Radj, how much is the increase in the no load speed of the motor? Hint: For linear interpolation in the interval, the formula to obtain the unknown point in this interval is as follows: Yo(x1 - x) + y1(x – x) y = X1 - Xo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve.the question given below
. A Short Shunt Compound DC Generator supplies 100-amp at 110-volt. Series field resistance of 0.04-ohm, armature resistance is 0.05-ohm, shunt field resistance of 57- ohm. Iron and friction losses mount to 852-watts. Find the power input and the over all efficiency.
A A permanent magnet DC motor has an armature resistance supplied by a 75-V DC Source, 1.4 S2. When it n svy t no-load speed d 2200 pm and draws 1.7 A. a) what 6.) What is the rotational'loss ? TS the output power (in hp) when it is operated at from 1800 rpm a 70-V DC source 7
At full load, when the DC shunt motor is supplied by 110 V dc source, the armature current is 20 A keeping the speed of the motor at 500 rpm. If the flux of the motor is weakened by 10%, the armature current drops to 15 A. By how much is the torque decreased?
the BLDC motors have the advantage of High Efficiency Compactness Low Maintenance All of the answers When the speed of the DC motor is Increases its Armature current Remain Constant Decreases Increases Any of the answers A variable reluctance stepper motor is constructed of .. . material with salient poles. ferromagnetic paramagnetic non-magnetic diamagnetic
Draw the circuit please.
A 200 V D.C. shunt motor takes 20 A at rated voltage and runs at 1000 r.p.m. Itsarmature resistance is 0.1 ohm. Calculate the value of additional resistance requiredin the armature circuit to reduced the speed to 800 r.p.m when the load torque isindependent of the speed.Ignore the field current. (Ans.1.98 ohm)
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 3 ALoad torque=Tload= 8 Nma) 143 rpmb) 734 rpmc) 1361 rpm d) 77 rpm e) 1333 rpm
I need the answer as soon as possible
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
A 230-V dc shunt motor takes a current of 5A at no-load. The resistance of armature and field circuits are 0.50 ohm and 230 ohm, respectively . If the maximum efficiency occurs at full load current, what is the value of this current? A 14 hp, 240 v shunt motor draws an armature current of 50 A at full-load. The armature resistance including brushes is 0.25 ohm. Calculate the total resistance of a starting box which wound permit this motor to develop a starting torque equal to twice that at full load.
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm