A 1 hydrostatic extrusion 2 Strain hardening 3 High temperature 4 Anisotropy in blank metal 5 n=0 6 Friction 7 Indirect Extrusion 8 Barreling 9 Floating plug 10 Blank form 11 Explosive forming 12 Impact load 13 Capstan 14 Bottoming 15 Bar drawing 16 Rolling, extrusion, forging B n reduces Metal flow is retarded Single draft operation Spring Back is reduced Hammers Metal increases its strength at room temperature Very short time forming process. Difficult to support the product when it exit's Open die forging Wire drawing Bulk metal forming Fluid applies force Tube drawing Controls the metal flow under the holder Occurs in Hot forming Earing Answer from A

A 1 hydrostatic extrusion 2 Strain hardening 3 High temperature 4 Anisotropy in blank metal 5 n=0 6 Friction 7 Indirect Extrusion 8 Barreling 9 Floating plug 10 Blank form 11 Explosive forming 12 Impact load 13 Capstan 14 Bottoming 15 Bar drawing 16 Rolling, extrusion, forging B n reduces Metal flow is retarded Single draft operation Spring Back is reduced Hammers Metal increases its strength at room temperature Very short time forming process. Difficult to support the product when it exit's Open die forging Wire drawing Bulk metal forming Fluid applies force Tube drawing Controls the metal flow under the holder Occurs in Hot forming Earing Answer from A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An L-shaped structural section is directly extruded from an aluminum billet in which Lo = 500 mm and Do = 100 mm. Dimensions of the cross section are given in Figure 1. Die angle = 90°. Determine (a) extrusion ratio, (b) length of the extruded section if the butt remaining in the container at the end of the ram stroke is 25 mm. 62 12 -50 Figure 1 12
Anisotropy in a metal O increases residual stresses. O properties vary with direction. increase the amount of toughness. increase the amount of springback. explosive forming increase the degree of ductility. O increases the strain hardening exponent. Vacuum line in the die is found in forging Tolling wire drawing deep drawing explosive forming Bending extrusion bar drawing
19 In the open die forging ,a high precision is obtained. Select one: True False
I need the answer as soon as possible
Which of the following operations are closely related to open-die forging: Select one: a. Coining b. Hobbing c. Upsetting d. Flashless forging
A cylindrical 4135 cold-rolled steel workpiece has an upsetting load applied at room temperature using an open-die forging with flat dies to a new height, ha = 50 mm, as shown below. The initial diameter is do = 220 mm, the initial height is ho = 180 mm. 4135 cold-rolled MPa=1100 Psi= 16000 Strain hardening exponent, n = 0.14 A) What is the diameter of the forging at the end of the forging stroke? B) What is the longitudinal true strain of the forging at the end of the forging stroke? C) What is the true (flow) stress required in the material at the end of the forging stroke? D) Using the average pressure formula, what is the corresponding coefficient of friction if the upsetting force at the end of the stroke is 170 MN?
Aluminium and copper wires can be made by cold drawing process. Select one: True False Planing operation is an example of ________________ Crushing is an example of ____________
None
Q4(a) Identify at least FIVE (5) factors that affect the Force, F in Figure
Homework: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to=40mm, tF35mm, C=415MPA, m=0.02, w=60c one pass rolling. Find Froll, T and Power.
Q2) Answer the following questions: 1. Is there any effect for the selection of the parting line in close die forging? Why? 2. How can you identify the optimum extrusion die angle? 3. Is there any advantage of the Hydrostatic Extrusion and is it possible to use it for the brittle materials? Why? 4. How would you fabricate the cam shaft in your car? Why? 5. How would you fabricate Nails (after the blanks have been made)? Why?
Homework: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to=40mm, tF35mm, C=415MPA, m=0.02, w-60cm one pass rolling. Find Froll, T and Power.