A 0.3-m3 rigid tank is filled with saturated liquid water at 200ºC. A valve at the bottom of the tank is opened, and liquid is withdrawn from the tank. Heat is transferred to the water such that the temperature in the tank remains constant. Determine the amount of heat that must be transferred by the time one-half of the total mass has been withdrawn. Answer in kJ

Q: an insulated piston-cylinder assembly initially at constant pressure of 250 kPa There is 4 L of…

A: Given data:   Pressure of piston-cylinder assembly = 250 kPa Volume of saturated liquid water = 4 L…

Q: If steam is heated in a rigif tank and its internal energy increases by 500 kJ, find the heat input…

A: As the tank is rigid there will be no change in the volume and hence no work done by the steam. If…

Q: A fluid system undergoes a non-flow frictionless process following the pressure-volume relation as p…

A:

Q: There is 7 bar pressure and 200 o C hot steam in a tank. This steam is allowed to cool in constant…

A:

Q: A truck tire is inflated to 250 kPa, and driven around for a while. After some time (assuming no…

A:

Q: Water at 200 kPa and 300 K (H=343.4 kJ/kg) enters a straight horizontal pipe at a velocity 3 m/s…

A: For water Inlet pressure = 200 KPa  Inlet temperature = 300 K  Inlet enthalpy = 343.4 KJ/kg  Inlet…

Q: If the suction pressure of compressor equal to discharge pressure then the work of compression for…

A:

Q: Find the average power of the paddle wheel in kW During a constant-pressure process in a cylinder…

A: The average power for the wheel of a paddle is to be determined in kW.

Q: a closed, rigid tank contains only water vapor and has a dew point of 50 Celsius. the total mass of…

A: Given, The dew point of water, Td = 50 °C The temperature of the water, T = 70 °C

Q: Compressed air at room temperature (295 K) is contained in a 20-L tank at 2 bar. The valve is opened…

A:

Q: An automobile engine provides 596 Joules of work to push the pistons and generates 2246 Joules of…

A: Given that, Work done on the system W = 596 J Heat generated by the system Q = 2246 J It is required…

Q: A cylindrical vessel with 2 m diameter and 4 m length initially contains R-134a at 1 MPa, 100 degree…

A: Given Data  Diameter of the vessel (D) = 2m Legth of the vessel (L) = 4 m Hence , the volume of the…

Q: Consider the piston-cylinder arrangement shown, in which the friction-free piston is free to move…

A:

Q: Steam is generated in a boiler. Water enters the boiler as saturated liquid at 7 MPa and leaves as…

A:

Q: Problem 1: One kg of water is placed inside a well-insulated piston. The external pressure PE is…

A: External pressure= 10 MPa Initial temperature of water= 20 0C Final temperature of liquid = 400 0C…

Q: Determine the rate of condensation of steam in Kg/h.

A: Properties at saturated steam pressure of 84.55 kpa or 0.8 bar Tsat = 366.66 K ρv = 0.479 kg/m3 hfg…

Q: The temperature of a mole of perfed gas is Increased from 300 to 500 k. What is the change in…

A: Given data: Initial temperature=300K Final temperature=500K We need to calculate the change in…

Q: A rigid tank is divided into two equal sections by a diaphragm. Initially, one of the sections has a…

A:

Q: The pressure is reduced to 872 kPa by cooling the steam at 4 MPa and 548 K at a fixed volume. The…

A: Total change in the entropy is asked. Given: P1=4×106 PaP2=872×103 PaT1=548 KT2=288 KSpecific heat…

Q: A & B are rigid tanks. Tank A has volume of 1 m, contains steam with 4 MPa and 500 °C heated by…

A:

Q: pressure increase

A:

Q: Saturated water vapor at 100 kPa is in a piston-cylinder device. At the initial state the piston is…

A:

Q: Natural gas with a molar analysis of 60% CH4, 30% C,H6 and 10% N2 enters a reactor and burns…

A: Composition of Natural Gas: CH4- 60% C2H6- 30% N2-10% Air is 20% excess To, a) Write the balanced…

Q: Indicate which statement is wrong: a. The best gases to use in cooling systems are gases with a high…

A: Throttling process is a process in which a fluid is passes through a restriction (small opening),…

Q: in a closed system process, 600 Btu of heat is added to the system, and the internal energy of the…

A:

Q: Two hundred kJ of work is transferred to the air by means of a paddle wheel inserted into an…

A:

Q: A piston cylinder assembly initially contains 5 kg of water, a saturated liquid vapor mixture at a…

A:

Q: A 1 m diameter cylinder, 1 m long, is maintained at 800 K and has an emissivity of 0.65. Another…

A: