90 kN 70 kN (1) (2) A C 90 kN 0.85 m 1.15 m

Q: 8. Plot a graph of the internal axial forces in segments AB, BC and CD vs. distance measured from A…

A:

Q: Aluminum [E= 70 GPa] member ABC supports a load of 28 kN. Determine: (a) the value of load P such…

A:

Q: 2. The half section of an arc is under a uniformly varying load. If the weight of the arch is 50,000…

A: The centroid of a body is the point where all sides have equal volume. The centre of mass of a solid…

Q: In the figure shown, each of the four vertical links connecting the two rigid horizontal members is…

A:

Q: #3. The distributed load w is supported by three suspender bars as shown. AB and EF are made of…

A:

Q: 4. A round, horizontal, simply supported steel bar is subject to an axial compressive load, P = 5…

A: Given data,Axial compresive load P=5KN=5000 NMaximum diflection δmax=350 mmDiameter of steel bar d=…

Q: For Questions 1-2 The rods CE (A = 130 mm²) and DF (A = 250 mm²) are attached to the rigid bar ABCD…

A:

Q: Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.125 in. thick,…

A:

Q: 1. In the figure shown, a variable- area shaft is subjected to the two loads F in each third of its…

A:

Q: Determine the magnitude of the vertical force Cy for the simply supported beam, where w = 10…

A:

Q: Two PARALLEL springs A and B has spring constants 269 N/mm and 91 N/mm, respectively. If the…

A: here, equivalent stiffness in parallel connection Keq. = 269 + 91 = 360 N/mm here, F = Keq. ×…

Q: sectional area of A is 1.80 mm^2 and that of B is 4.20 mm^2 . Young's modulus for wire A is…

A: Given: Total length of the rod is 1.05 m. Area of A is 1.80 mm^2 . Area of B is 4.20 mm^2.

Q: The rigid arm AB is attached to the end of the solid circular steel rod BC. The rod is supported by…

A:

Q: Determine the deflection in inches of a .75" diameter steel shaft 13" long subject to an axial force…

A: Given, Shaft diameter is 0.75 inch Length of shaft is 13 inch Axial force is 1600 N Required:…

Q: В D 6 kN 5 kN 4 kN A - 2 m→2 m→ -3 m- -3 m

A:

Q: Question Both portions of the rod ABC are made of an aluminum for which E = 69.2GPA. Knowing that…

A:

Q: Using an energy or work approach, determine the vertical deflection of point C and the deflection of…

A:

Q: An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a…

A: Bar 1: Cross sectional area, A1= 760 mm2Elastic modulus, E1= 28 GPa= 28000 MPaLength, L1= 0.85 m=…

Q: The hollow square cross section shown has a wall thickness, T, of 10.9 mm. Determine the second…

A: The moment of inertia of the big square can be determined as shown below.

Q: Consider a car of mass 1200 kg with a ground clear- ance of 390 mm supported by four springs of…

A:

Q: The steel bars AC and BC, each of cross-sectional area 120 mm^2, are joined at C with a pin.…

A:

Q: A rectangular beam is 12 meters long. It is supported by R1 at the left end and R2, 4 meters from…

A: Solution is given below:

Q: 3. A beam is loaded and supported as shown below. Use singularity functions and the integration…

A:

Q: y? = 1.5x 1.225m P1 The steel plate is 0.1 m thick and has a density of 7500 kg/m. Determine the…

A: Consider the steel plate given as composed of two segments. The parabolic part above x axis as part…

Q: A uniform bar of length L, cross-sectional area A, and unit mass p is suspended vertically from one…

A:

Q: Determine the crippling load for a T-section of dimensions 12 cm x 12 cm x 2 cm and 5 m long which…

A: Given data as per the question Dimensions of T section =12 cm×12cm×2cm Lenth =5 m Young modulus…

Q: termine the magnitude of the vertical force Cy for the simply supported beam, where w = 10 kips/ft,…

A: Ans: 38.5 kips

Q: PROBLEM 3. The aluminum rod has a solid circular cross-section and supports the loading shown.…

A:

Q: 3. The rigid bar BDE is supported by two links AB and CD. Link AB is made ol steel (E=200 GPa) and…

A:

Q: A 7/8-in.-diameter rod BC is attached to the lever AB and to the fixed support at C. Lever AB has a…

A: Given data as per the question The diameter of rod BC =7/8 in Force applied on the Lever =80 lb E=29…

Q: 2 kN.determine the deflection (in

A: To find deflection of Point-A

Q: the cross-section through point D Determine the resultant nternal loadınigs in Fig. 2. Assume the…

A:

Q: 1. The timber member has a cross-sectional area of 1700 mm2 and its modulus of elasticity is 12 GPa.…

A:

Q: Rigid bars AB and BCD are supported by pins A and D and by a steel rod at C. There is a roller E =…

A:

Q: 10.15. Find the maximum load that the system can support before buckling. Material steel and…

A:

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A:

Q: Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.2 sq.in. Knowing…

A:

Q: 5. Two C310x45 channels are latticed together so they have equal moments of inertia about the…

A:

Q: A steel rod having a length of 50 m is suspended vertically from one end. It supports a tensile load…

A: As per given  P=7850kg/m3 E=200 GPA Allowable stress =140 mpa We have to find determine the diameter…

Q: The triangular block below is subjected to the Loads P=1200 lb and 400 lb. If AB=8 in, and BC is…

A: Truss is a group of two forces. Only at the joints are forces applied. The forces in truss members…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.