9.12 Water flows past a flat plate that is oriented parallel to the flowwith an upstream velocity of 0.5 m/s. Determine the approximatelocation downstream from the leading edge where the boundary layerbecomes turbulent. What is the boundary layer thickness at thislocation?9.13 A viscous fluid flows past a flat plate such that the boundarylayer thickness at a distance 1.3 m from the leading edge is 12 mm.Determine the boundary layer thickness at distances of 0.20, 2.0, and20 m from the leading edge. Assume laminar flow.

Answered: Image /qna-images/answer/6e0be93b-f1c3-4c6d-b49a-8162151695f4.jpg

0.12 Water flows past a flat plate that is oriented parallel with an upstream velocity of 0.5 m/s. Determine the ap ocation downstream from the leading edge where the bour ecomes turbulent. What is the boundary layer thickn ocation? 2.13 A viscous fluid flows past a flat plate such that the ayer thickness at a distance 1.3 m from the leading edge Determine the boundary layer thickness at distances of 0.2 10 m from the leading edge. Assume laminar flow.

0.12 Water flows past a flat plate that is oriented parallel with an upstream velocity of 0.5 m/s. Determine the ap ocation downstream from the leading edge where the bour ecomes turbulent. What is the boundary layer thickn ocation? 2.13 A viscous fluid flows past a flat plate such that the ayer thickness at a distance 1.3 m from the leading edge Determine the boundary layer thickness at distances of 0.2 10 m from the leading edge. Assume laminar flow.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A line load of q=60kn/m with alpha =300 is placed on a ground surface as shown in figure p4.1.Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z=10m ,X=0m ,v=0.5 ,A=0.45 (b) z=10m, X=2m,v=0.45, A=0.6
When soil water potential in a sandy loam soil goes from -0.1 to -10 bars, the height of an equivalent column of capillary water increases 100 times. The rate of water movement (the hydraulic conductivity): O increases by a factor of about 100 times increases by a factor of about 10 times remains little affected O decreases by a factor of about 1000 times decreases by a factor of about 10 times
Calculate the effective hydraulic conductivity for flow parallel and perpendicular to layering. Please show and explain the difference in values.
Given: Permeability, k = 40 x 104 cm/s Saturated unit weight of the soil = 20 kN/m³ Other information shown in the Figure E3-3 Determine the following: (a) Quantity of Discharge (b) Total vertical stress at Points B and D (c) Pore-water pressure at Points B and D (d) Effective vertical stress at points B and D 20.0 m 6.5 m 5.0 m 10.5 m Water YAY Concrete Impervious Figure E3-3 1.0 m VAYAYAY 5.0 m
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. Determine the circumferential stress in the tank.
Hydraulic conductivity (K) in the vadose (unsaturated) zone is affected by of the following subsurface properties. Select all that apply. moisture content Fick's condition Zubov's condition Pore water pressure Darcy's condition Hysteresis wetting/drying stage Gregorian chant in e minor
A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the figure (not drawn to scale) 55.2 m BT Peizometer P Reference Datum Aquiclude Piezometric Surface Aquiclude Peizometer Q L = 2500 m 34.1 m ונטוב SOM The heads indicated by two piezometers P and Q are 55.2 m and 34.1 m, respectively. The aquifer has a hydrau- lic conductivity of 80 m/day and its effective porosity is 0.25. If the distance between the piezometers is 2500 m, the time taken by the water to travel through the aquifer from piezometer location P to Q (in days, round off to 1 decimal place) is
2. Nitrogen gas at 15 °C has a density of 0.07616 Ibm/ft³ with a kinematic viscosity of .146 cm²/s forms a boundary layer near a solid wall. The velocity distribution in that boundary layer is given by the expression u = 1-e where U = 15 m/s and 8 = 1.2 cm. Find the shear stress at the wall (y=0.005 m).
Question 4.8 Consider a layered reservoir consisting of three alternating layers 1 m thick and 1 m long, with k,= 1000 mD, k, = 100 mD, and k,= 10 mD. a) What is the average permeability of this reservoir if the fluid is flowing parallel to the layering (k,)? b) What is the average permeability of this reservoir if the fluid is flowing perpendicular to the layering (k,)? c) What is the kJk,?
4.1 A line load of q = 60kN/m with a = 0 is placed on a ground surface as shown in Figure P4.1. Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z = 10m, x = 0m, v=0.5, A=0.45. (b) == 10m, x= 2m, v= 0.45, A=0.6. 2 m 4. G.W.T. Clay XI 1
For a falling head permeability test, the following values are given: Length of specimen: 200 mm Area of specimen:1000 sq. mm Area of standpipe: 40 sq. mm Head difference at t= 0: 500 mm Head difference at t= 180 sec : 300 mm Determine the hydraulic conductivity (cm/sec)
Figure Q.3 shows a liquid reservoir that is density stratified. The top layer has thickness b and uni- form density pt. The middle layer has thickness d and a linearly varying density given by Pt (") (h - b) Pb - Pt P(h) = Pt+ d p(h) for (b Pt. Figure Q.3. Use the information provided above and in Figure Q.3 to derive the gauge pressure distribution for the liquid in the reservoir.