4. Is Turbulent Flow Possible? Water flows through sand with an average particle size of 0.70 mm. Assume that the average water temperature in the subsurface is 15 C. What is the maximum velocity of laminar flow through this material? What gradient is required to produce such a velocity assuming the sand's hydraulic conductivity is approximately 102 cm/s? Is that gradient physically possible under natural conditions?

4. Is Turbulent Flow Possible? Water flows through sand with an average particle size of 0.70 mm. Assume that the average water temperature in the subsurface is 15 C. What is the maximum velocity of laminar flow through this material? What gradient is required to produce such a velocity assuming the sand's hydraulic conductivity is approximately 102 cm/s? Is that gradient physically possible under natural conditions?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.9P

See similar textbooks

Similar questions

2. Sand at a given relative density has a friction angle of approximately 33° (relatively low stress). When the sample is unsaturated at a given value of saturation (not given to you), the specimen has a negative pore pressure of 5 kPa. How tall a sandcastle "vertical" wall can you construct? What would happen to your sandcastle if the level of saturation suddenly increased? (Assume a total unit weight of 18 kN/m³)
[Seepage] tank shown below. For the sand, the following properties are given: e = 0.40 , G.S = 2.67 . Calculate the effective stress at A. a. Consider the upward flow of water through a layer of sand in a 1.2m Overflow 0.7 m Sand z = 0.9m 2 m Inflow
The hydraulic conductivity of a sand at a void ratio of 0.62 is0.03 cm/sec. Estimate its hydraulic conductivity at a void ratioof 0.48.
The hydraulic conductivity of a sand at a void ratio of 0.750 is 0.047 cm/s. Estimate the coefficient of permeability at a void ratio of 0.450 1. Using Casagrande equation 2. Using Kozeny-Carman equation
A glass container with pervious bottom containing fine sand in loose state (void ratio = 0.8) is subjected to hydrostatic pressure from underneath until quick condition occurs in the sand. If the specific gravity of sand particles = 2.65, area of cross-section of sand sample= 10 cm2 and height of sample = 10 cm, compute the seepage force in N acting from below. a. 9.17. b. 0.9 c. 0.45 d 7.29
From the figure shown, the void ratio of the sand is 0.55 with a specific gravity of 2.68. The cross-sectional area of the tank is 0.5 sq.m and hydraulic conductivity of sand = 0.1 cm/s. a. What is the rate of upward seepage in cu.m/hour? b.Determine the critical hydraulic gradient for zero effective stress. c. Determine the value of h (head loss) to cause boiling. NEED ASAP. THANK YOU.
A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.
Problem Ex. Consider the upward flow of water through a layer of sand in a tank as shown in Figure. 1.5 m 0.7 m I m 2 m Valve (open) Inflow O Sand For the sand, the following are given: void ratio (e) = 0.52 and specific gravity of solids (G.) = 2.67. Calculate the total stress, pore water pressure, and effective stress at points A and B. What is the upward seepage force per unit volume of soil? Total stress, porewater pressure, effective stress. Point A t B Total stress (kN/m?) Porewater pressure Effective stress Upward seepage force.
CVE 331: Theoretical hydraulic conductivity calculation Problem 1: The hydraulic conductivity of a sandy sol is 7x10 cm/sec at void ratio 0.68. What is the hydraulic conductivity at void ratio 0.85 ? (o.re) A= 2,42e k2 ei Problem 2: The hydraulic conductivity of a clay soil is 121o* cm/sec at void ratio 0.56, and 3.1x10 cm/sec at void ratio 0.74. What is the hydraulic conductivity the soll at void ratio 0.65 ? e3 ki %3D - 3. 797 GRAIN SIZE DISTRIBUTION GRAPH. A- PROJECE
1. (30 pts) The soil profile shown below consists of 10 meters of sandy silt overlying gravel. The pore water pressure at the top surface of the silty sand is zero and can be assumed to remain zero. a) Calculate the level to which water would rise in a piezometer tube inserted into the top of the gravel if the silty sand is just stable? Use submerged unit weights and seepage forces to arrive at your answer (do not calculate total stresses and pore water pressures). Express your answer as an elevation, e.g. "Elev. 130". (Note: Elevations are in meters) (10 pts) b) Using the piezometric elevation calculated in part (a), calculate the pore water pressure at the bottom of the silty sand if the silty sand is just stable (10 pts). c) Calculate the total stress at the base of the silty sand and show that it is equal to the pore water pressure calculated in part (b) (10 pts) Elev. 120 m. Elev. 110 m. Sandy Silt (saturated) Void ratio, e = 0.68 G = 2.65 Gravel
topic: geotechnical engineering The ground water level in a thick, very fine sand deposit is located at 2.0 m below the ground surface. Above the free ground water, the sand is saturated by capillary action. The unit weight of the saturated sand is 20.3kN/m^3 a. total stress located at 4.5 m below the ground surface b. Pore water pressure at 4.5 m below the ground surface c. Effective stress 4.5 m below ground surface
i. A sandstone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 6.21 cubic centimetres per second. The length of the core sample is 14 centimetres and its diameters is 6 centimetres. The pressure differential across the core sample is 15 atmospheric pressure and the water viscosity is 1.2 centipoises. Explain a method of how the permeability of low permeability reservoirs can be ii. improved.