A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the figure. (not drawn to scale) Piezometer P MMATim 55.2m Piezometric Surface Aquiclude Aquifer REEF Aquiclude L=2500m Piezometer Q 77728 34.1m The heads indicated by two piezometers P and Q are 55.2 m and 34.1 m, respectively. The aquifer has a hydraulic conductivity of 80 m/ day and its effective porosity is 0.25. If the distance between the piezometers is 2500 m, the time taken by the water to travel through the aquifer from piezometer location P to Q (in days, round off to 1 decimal place) is.

A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the figure. (not drawn to scale) Piezometer P MMATim 55.2m Piezometric Surface Aquiclude Aquifer REEF Aquiclude L=2500m Piezometer Q 77728 34.1m The heads indicated by two piezometers P and Q are 55.2 m and 34.1 m, respectively. The aquifer has a hydraulic conductivity of 80 m/ day and its effective porosity is 0.25. If the distance between the piezometers is 2500 m, the time taken by the water to travel through the aquifer from piezometer location P to Q (in days, round off to 1 decimal place) is.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 4-cell aquifer model is conceptualized in the figure below. River Cell 1 Cell 2 Cell 3 (a) Top view (b) Cross section Cell 4 Impervious boundary The width of the aquifer strip is 3.0 km; the length of each cell is 5 km. The recharge rates for the aquifer strip is 400 mm/yr, 300 mm/yr, 300 mm/yr, 200 mm/yr in Cells 1,2,3, and 4,respectively. The water level in the river is maintained at a constant elevation of 160 m above the horizontal impervious bottom. The hydraulic conductivity in Cells 1 and 2 is 3 m/d, while in Cells 3 and 4 it is 6 m/d. Using this conceptual model, determine: 1. Write the steady-flow balance equations to estimate average water levels in the four cells. 2. Solve these equations to determine the average elevations in the 4 cells without pumping. 3. Solve these equations when pumping takes place in Cells 2 and 3 at rates of 4×106 m3/yr and 7×106 m3/yr, respectively.
A syphon of diameter 200 mm connects two reservoirs having a difference in elevation of 15 m. The total length of the syphon is 600 m and the summit is 4 m above the water level in the upper reservoir. If the separation takes place at 2.8 m of water absolute, find the maximum length of syphon from upper reservoir to the summit. Take f= .004 and atmospheric pressure = 10.3 m of water.
A line load of q=60kn/m with alpha =300 is placed on a ground surface as shown in figure p4.1.Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z=10m ,X=0m ,v=0.5 ,A=0.45 (b) z=10m, X=2m,v=0.45, A=0.6
A 1-m diameter well penetrates vertically through a confined aquifer 30 cm thick. When the well is pumped at 113 m³/hr, the drawdown in a well 15 m away is 1.8 m, in another well 50 m away, it is 0.5 m. What is the approximate head in the pumped well for steady state conditions and what is the approximate drawdown in the well? Also compute the transmissivity of the aquifer and the radius of influence of the pumping well. Take the initial piezometric level as 40 m above the datum.
The volume of a reservoir is 2×107 m3, the catchment area is 500 km2, the average annual inflow of rivers and streams is 800 mm, and the annual silt entering the reservoir is 320 ton/km2, assuming that the proportion of silt is 1800 kg/m3, Assuming that the sand trapping rate of the reservoir is y, the ratio of the reservoir capacity to the annual inflow is x, and the relationship between the two is y=1+0.1*lnx. try to estimate the number of years required for 80% of the initial reservoir capacity to fill up?
.A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the figure (not drawn to scale) Piezometer P 55.2m Piezometric Surface Aquiclude Aquifer Aquiclude Piezometer Q L = 2500m 34.1m The heads indicated by two piezometers P and Q are 55.2 m and 34.1 m, respectively. The aquifer has a hydraulic conductivity of 80 m/ day and its effective porosity is 0.If the distance between the piezometers is 2500 m, the time taken by the water to travel through the aquifer from piezometer location P to Q (in days, round off to 1 decimal place) is
9) A well is located in a confined aquifer near the intersection of a constant head and impervious boundary. a) Estimate the steady state drawdown in the well for Q=2 ft³ s, rw = 1 ft, distance from the well to stream= 300ft and distance from well to impervious boundary= 150 ft. T = 0.14ft²/s b) Estimate the steady state drawdown at point P located midway between the well and the steam. The angle between the stream and the impervious boundary is 90°
A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the figure (not drawn to scale) 55.2 m BT Peizometer P Reference Datum Aquiclude Piezometric Surface Aquiclude Peizometer Q L = 2500 m 34.1 m ונטוב SOM The heads indicated by two piezometers P and Q are 55.2 m and 34.1 m, respectively. The aquifer has a hydrau- lic conductivity of 80 m/day and its effective porosity is 0.25. If the distance between the piezometers is 2500 m, the time taken by the water to travel through the aquifer from piezometer location P to Q (in days, round off to 1 decimal place) is
1) A dry rock weighs 240 grams and has a bulk density of 2.5 grams per cubic centimeter. Whensaturated with pure water at room temperature (T = 25 °C), it weighs 255 grams. At room temperature,specific volume of water is 1.00295E-03 m3/kg. Calculate the porosity of the sample. 2) A cylindrical core sample of 1.5 cm length and 1.2 cm2cross-section has upstream and downstreampressures of 2 atm and 1.25 atm, respectively, during steady state flow of water at 1.00 g/s at roomtemperature. Calculate the permeability of the core. (Water @ 25 °C, viscosity = 1 cp, density of water = 0.997 g/cm3).
A smooth flat plate with a sharp leading edge is placed along a free steam of water flowing at 2.5 m/sec. At what distance from the leading edge will the boundary layer transition from laminar to turbulent flow? Take density of water as 1000 kg/m³ and its viscosity as 1 centipoise. Also, what will be the boundary layer thickness at that distance?
Question 4.8 Consider a layered reservoir consisting of three alternating layers 1 m thick and 1 m long, with k,= 1000 mD, k, = 100 mD, and k,= 10 mD. a) What is the average permeability of this reservoir if the fluid is flowing parallel to the layering (k,)? b) What is the average permeability of this reservoir if the fluid is flowing perpendicular to the layering (k,)? c) What is the kJk,?
Figure Q.3 shows a liquid reservoir that is density stratified. The top layer has thickness b and uni- form density pt. The middle layer has thickness d and a linearly varying density given by Pt (") (h - b) Pb - Pt P(h) = Pt+ d p(h) for (b Pt. Figure Q.3. Use the information provided above and in Figure Q.3 to derive the gauge pressure distribution for the liquid in the reservoir.