9. A trapezoidal load is acting in the middle portion AB of the double side overhanging beam as shown in the Fig. given below. A couple of magnitude 10 kNm and a concentrated load of 14 kN acting on the tips of overhanging sides of the beam as shown. Draw SFD and BMD. Mark salient features like maximum positive, negative bending moments and shear forces, inflection points if any. 14kN 40kN/m 20kN/m 50% 10kNm

9. A trapezoidal load is acting in the middle portion AB of the double side overhanging beam as shown in the Fig. given below. A couple of magnitude 10 kNm and a concentrated load of 14 kN acting on the tips of overhanging sides of the beam as shown. Draw SFD and BMD. Mark salient features like maximum positive, negative bending moments and shear forces, inflection points if any. 14kN 40kN/m 20kN/m 50% 10kNm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The resultant of the rectangular load is _______ from point B.
Find stress
15 mm PROBLEM 6.9 -250 mm 65 kN 90 kN 65 kN 0.3 m (300 пm) For the beam and loading shown, consider section n-n and determine (a) the largest shearing stress in that section, (b) the shearing stress at point a. 25 mm 250 mm 10 mm 15 mm 06 m 06 m 06m 06 m
9.14. A load P = 12.0 kN is applied to the clamp shown in Fig. P9.14. Deter- mine the circumferential stresses at points B and C, assuming that the curved beam formula is valid at that section. ↓ 26 mm Figure P9.14 -76 mm- 12 mm 68 mm - 73 mm 36 mm- B 36 mm 22 mm
Don't be confused, the 10 kn will be 18 kn and 15kn/m will be 31 kn/m. Disregard the id things. Upvote guaranteed
incorrect solution will receive the negative rating ......A 60 ft. beam supports two applied distributed loads, a distributed load w1-248 pounds her linear foot (plf) and distributed load two d2=125 pounds per linear foot (plf). In addition, the estimated weight of the beam is 55 pounds per linear foot. Calculate the magnitude (in pounds) of the horizontal and vertical components of reactions at supports A and B.
ACTIVITY Compute for the shearing stress in the pin at B for the member supported as shown in the figure. The diameter of the pin is 20mm. K.R.R.P. 00 Pin at B 200 mm- 40 KN AL B 250 mm
Determine the maximum shear stress in the T-beam at point C. 150 mm 10 kN/m T 150 mm 30 mm |C --30 mm 5m +₁. 3 m- -1.5 m-1.5 m- A B
569
A В A uniformly distributed load is applied on a simply supported beam. What is the Maximum Shear (in kN) experienced by the beam? w = 30 kN/m L= 4.1 m w/
A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
The beam shown in Fig1.carries a concentrated load of W and a total distributed load of 8 W. Determine the maximum safe value W that will not exceed allowable stresses in tension of 60 MPa, in compression of 90 MPa, or in shear of 15 MPa. 1m W ᎦᎳ ? 15 2m 1m 20mm Fig.1 140mm 20mm 2 20mm 140mm