9. A reservoir contains 2.83 cu m of carbon monoxide at 6895 kPa and 23.6°C. An evacuated tank is filled from the reservoir to a pressure of 3497 kPa and a temperature of 12.4°C, while the pressure in the reservoir decreases to 6205 kPa and the temperature to 18.3°C. What is the volume of the tank? R for CO is 296.92 J/kg.Ko. Ans. 0.451 m

9. A reservoir contains 2.83 cu m of carbon monoxide at 6895 kPa and 23.6°C. An evacuated tank is filled from the reservoir to a pressure of 3497 kPa and a temperature of 12.4°C, while the pressure in the reservoir decreases to 6205 kPa and the temperature to 18.3°C. What is the volume of the tank? R for CO is 296.92 J/kg.Ko. Ans. 0.451 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
A rigid tank (0.010 m³) contains saturated liquid water at 160 deg C. How much heat (kJ) must be added for the pressure to be 800 kPa and a temperature of 200 deg C?
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Oxygen is heated from 700 to 1000 R. Determine the enthalpy energy change Ah of oxygen, in Btu/lbm, using the cp value at the average temperature from the table. (You must provide an answer before moving on to the next part.) The enthalpy energy change of oxygen is 218 Btu/lbm.
Either the system illustrated below where the fluid considered is water. 1. Calculate: (a) the internal energy (specific), and (b) the mass finally remaining in the volume of Control. 2. In the control volume, what is: (a) the specific internal energy of the saturated steam, (b) The specific internal energy of the saturated liquid, and (c) the (final) temperature? 3 kg. 30 m 100 kPa, 160°C 2 kg, 10 m 100 kPa, 140°C, 200 m/s 3 2 1 kg, 0 m 100 kPa. 100°C, i 1000 m/s ++ Q=9200 kJ mini= 10 kg 100 kPa, x=0.6 min= ? kg 100 kPa, Uin=? +7 kg, 20 m 4 100 kPa, 150°C 8 kg. 0 m 5 100 kPa. 130°C, 100 m/s
1) A 10 Liter pressure cooker has an operating pressure of 400 kPa. Initially, % of the volume is filled with saturated water and the rest is saturated vapor. What temperature is the vessel? After heating for 5 hours, the pressure cooker ran dry. What was the average rate of heat transfer?
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A piston-cylinder device initially contains 1 kg saturated liquid water at 200°C. Now heat is transferred to the water until the volume quadruples and the cylinder contains saturated vapor only. The saturated liquid properties of water at 200°C 3 are vf= 0.001157 m³/kg and uf- 850.46 kJ/kg (Table A-4). Water mkg 200°C Q Determine the final temperature and pressure. (You must provide an answer before moving to the next part) The final temperature is The final pressure is °C. kPa.
With a volume of 200 L and a cylinder pressure of 100 kPa with the piston on the stopper a piston-cylinder assembly contains water with a degree of dryness of 50%. A pressure of 200 kPa is needed to move the piston up. Volume 400 The cylinder continues to be heated until it reaches According to this; a) This process takes into account the saturation line in the T-v and P-v diagram. show. b) Calculate the temperature in the final state. c) Find the work done. d) Find the amount of heat transfer.
Refrigerant-134a is in an insulated canister with temperature 25 C. There is a partition in the canister so the refrigerant is a saturated liquid and takes up 1/100 of the volume of the canister. The rest of the volume is evacuated. When the canister is activated by squeezing (no work done activating) the partition breaks and the refrigerant fills the total volume. Final pressure is 100 kPa. a.) What are two assumptions needed for the problem? What properties are needed to solve part b.) and c.) b.) What is the change in specific enthalpy within the canister? c.) What is the final quality of the refrigerant within the canister?
Required information m³/kg. A 1.76-m³ rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the rest is in the vapor form. The properties of steam at 220°C are given as follows: vf= 0.001190 m³/kg and vg = 0.08609 m NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Steam Vm³ 220°C Determine the pressure of the steam. The pressure of the steam is 2319.6 kPa.
An ideal gas follows the relationship pV=10 where V is in m3 and p is in kPaa. Draw the pV diagram and find the area under the curve (in kN-m) as the pressure decreases from 500 kPaa to 50 kPaa.
***Please show your correct and complete solution for this problem. Box your final answers and express in two decimal places. Sketch the schematic diagram.*** A rigid tank initially contains 5kg of saturated vapor steam at 150°C. Heat transfer is done until the pressure of steam reaches 1.20 MPa. Sketch the P-v diagram. Solve for the change in enthalpy and heat transferred.
Air in a rigid tank is at 200oC and 150 kPa. The air is cooled to a final equilibrium state of 60oC . i. Determine the change in pressure of the air, kPa. ii. Show and label the process on a temperature versus volume (P-v ) diagram. The gas constant for air, R is 0.287 kJ/kg.K and the universal gas constant, Ru is 8.314 kJ/kmol.K.