A conduit connects two receptacle of different size. A valve is used at each end which can be opened or closed. The first receptacle contains 300 liters  of air at 4,200 kPa, 82C. The second receptacle contains air at 75kPa, 9C.  Calculate the volume of the second receptacle if after the valve was  opened and the properties of the mixture were 2400kPa for the pressure,  and 52C for the temperature.

Q: A piston cylinder contains 11kg of air at 20 degC and 300 kPa. It is now heated up in a constant…

A:

Q: Q) Saturated (liquid+ vapor) ammonia at 60°C is contained in a rigid steel tank. The system is…

A: Given data T = 60°C Need to draw T-V diagram and determine the quality the pressure at the initial…

Q: 4 pounds of air in a closed container at 45 psi gauge, 60°F is heated to 130°F. Calculate the amount…

A:

Q: Water at 200 kPa with a quality of 25% has its temperature raised 30 C in a constant pressure What…

A: The initial pressure is The initial quality is The final pressure is The final temperature is

Q: Saturated uater vapour at 60i has its pressure decrease to increase the volume by 10%% Keeping the…

A: Given: T1=60°∆V=10%

Q: 10 kg of an ideal gas that is going through a large temperature change from 27degC to 1127degC while…

A:

Q: A conduit connects two receptacle of different size. A valve is used at e end which can be opened or…

A: To Find :  The volume of the second receptable  Given : The temperature of first receptacle is The…

Q: 1. A1 m³ tank containing air at 25'C and 500 kPa is connected through a valve to another tank…

A: Given:V1=1 m3T1=25°C =298 KP1=500 KPam2=5 KgT2=35°CP2=200 KPa

Q: Q2. A mass of 1000kg of saturated liquid water is completely vaporized in a isobaric (100kPa) heat…

A: Write the properties of saturated liquid and vapor at 100 kPa.

Q: An oxygen tank has a volume of 4 cubic meters and is at 20 degrees C and 700 kPa. The valve is…

A:

Q: Find the specific volume (m³/kg) for water at 10 kPa, 50°C Find the specific volume (m³/kg) for…

A: Given data  a) For water. 10kpa and 50°C  Find specific volume of water. b) for water , 200kpa and…

Q: Find the volume, the internal energy and the enthalpy of 2.5 kg of compressed liquid at 7.5 MPa and…

A:

Q: Example 2 An oxygen cylinder has a capacity of 300 L and contains O₂ at 3.1 MPa and 18 °C. The value…

A:

Q: There is nitrogen gas at a pressure of 500 kPa and a temperature of 300 K in a container with a…

A:

Q: Saturated liquid water at 500 kPa is throttled to a pressure of 200kPa. What is the finial…

A: According to the given data P1=500KPa and quality x=0 (Saturated liquid) P2=200KPa Throattling…

Q: For the situations below briefly explain how you obtained the values and provide the numerical…

A: It is required to determine properties for given process

Q: find the moisture content

A: Given: m=4.5 kg V= 9 m3 To determine: Moisture content At T=40oC T=60oC

Q: interpolations/extrapolations: NO Calculator Technique and Applications. 1. Five kilo of water…

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. Please…

Q: Water at 25C and a quality of 1% is contained in a spherical tank that has a diameter of .5m. The…

A: Given data: Initial Temperature of water = T1 = 25°C =298 KInitial Quality of water = 1%Diameter =…

Q: A rigid tank containssome liquid water at 300C. The rest of the tank is filled with atmospheric air.…

A: Here I'm going to tell that, how can be water boiled without raising it's temperature.

Q: A rigid tank contains air at a pressure of 70 psia and a temperature of 60F. By how much will the…

A:

Q: Gasoline, diesel fuel, jet fuel, and motor oil are examples of ?

A: To find : Gasoline, diesel fuel, jet fuel, and motor oil are examples of

Q: original Exio 2 kg o.7 m', had an temperature of 15.. It was Hhen heated at constant Volume until…

A:

Q: A 1.2m3 tank is filled with water mixture at 200C if 90% of the mass is liquid and the rest is vapor…

A:

Q: Derive the MEPotto  in terms of P1, rk, rp, k, and e.

A:

Q: A quantity of air is heated from 30 °C to 110 °C. Assume air is an ideal gas, in which is has…

A:

Q: how would you find the conditions of Saturated vapor at 1 MPa on a Mollier Chart

A:

Q: EX:- Determine the phase of the şubstance at the given state. a-water at 100 °C , 500 KPa

A: State is determined using property table.

Q: conduit connects two receptacle of different size. A valve is used at each end which can be opened…

A: Given: VA=300 L=0.3m3 PA=4200 Kpa TA= 82oC=355k PB=75 Kpa TB= 9oC=282k P2=2400 Kpa T2= 52oC=325 k…

Q: A conduit connects two receptacle of different size. A valve is used at each end which can be opened…

A: Given for first receptable vessel Pressure Pa = 4200 KPaTemperature Ta  = 82o C =82+273 K =355…

Q: Q2/ A 0.1 m' cylinder containing of oxygen has an externally loaded piston. Initially the oxygen at…

A: Given:V1=0.1 m3p1=400 KPaT1=200°CpV1.3=Cn=1.3T2=300°C

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.