Please show your work. Thank you! 1. 1 kg of water (saturated mixture) is at 30C as shown below. The piston has a cross sec-tional area of .0065 M^2 and a mass of 40kg. The piston is resting on the stops initially.The total volume of the cylinder is 100 L and the atmospheric pressure is 94 kPa. Heat isnow added until the system becomes a saturated vapor. Assuming a gravitational con-stant of 9.81 m/s^2, determine:a. The temperature of the water when the piston first rises from the stopsb. The total work done by the water during this processPatmStopsVaporLiquid

Answered: Image /qna-images/answer/b2f388e7-8795-464c-b2b2-8f4624c112ee.jpg

Answered: F.0065 M^2 and a mass ume of the…

Engineering

Mechanical Engineering

F.0065 M^2 and a mass ume of the cylinder is 10 ntil the system become. m/s^2, determine:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: uppose you are asked to conduct an experiment to study the impact of three factors(temperature: high…

A: Design of experiments (DOE) is nothing but a technique that is used to optimize the product cost and…

Q: Explain Modeling the Action of Forces

A: Given Data⇒ Action of forces Modelling

Q: Describe the relationship between force and surface area using specific quantitative examples. What…

A: This question is based on the concept of Pressure.

Q: Explain when we use sectional views and how they are made?

A: Sectional view are required when there is requirment to inspector understand the interior view of an…

Q: 1. In the bulk deformation process, there is a change in the thickness of the wokpiece. Thus, the…

A: 1)Explanation: Bulk deformation process like rolling , forming etc for constant thickness the length…

Q: Explain EXTERNAL WORK AND STRAIN ENERGY?

A: External work: Work is said to be done when energy created by all the processes taking place inside…

Q: b) With a neat sketch, identify and illustrate the metal forming processes for the following…

A: Forming, also known as metal forming, is a metalworking technique that involves the mechanical…

Q: F. 15° 700 N

A: Draw the FBD for the given question and find the angle between both the forces.

Q: What is a pictorial drawing? What are the different types of pictorial drawings?

Q: b-

A: GIVEN DATA A METAL PLATE IS GIVEN WE HAVE TO FIND ITS CENTRE COORDINATE X AND Y

Q: What are assessments that measure strength, speed, agility, or high-speed strength? What are the…

A: The assessments that measure strength, speed, agility, or high-speed strength is T-Test

Q: 1. A rod made from a material with a constitutive law of the form σ = 100 + 75€ 0.2 is drawn from a…

Q: How we can measure shear modulus?

A: The earth's material reaction to shear deformation is measured in shear modulus. The ratio of…

Q: Can someone rewrite the solution of this in a more readable and understandable way? thank you

Q: Are films stronger in the machine direction or the cross direction? Why?

A: MDO is achieved by pulling the film or sheet between two sets of rolls rotating at different speeds,…

Q: How might your machine or system be improved? What constraints might be involved in its design

Q: This is what I drew out. I'm unsure of hidden lines

A: Please refer the completed orthographic views of the given object. The drawing is made with the true…

Q: Give an example of the Absolute Maximum Shear Strain?

Q: Explain in your own words the sentence; “engineering drawing is the graphic language of engineers.”…

A: given; Explain in your own words the sentence; “engineering drawing is the graphic language…

Q: Could you provide an in depth definition of a moment of force including units as well as how…

A: Moment of Force:- A moment of force is defined as that is a measure of its tendency to cause a body…

Q: What is the force required to punch a 20-mm diameter hole in a plate that is 25 mm thick? Shear…

Q: Why should the thermal stresses be considered in design?

A: The stresses generated due to rapid heating or cooling of the structure are known as thermal…

Q: During plastic deformation anisotropy in sheet metals can: a have adverse effect during the…

Q: Question 2. It is reduced to 80 mm with forging by stacking a part with a height of 120 mm and a…

Q: With suitable sketches of the relationship of friction force and applied load, briefly explain the…

Q: What is the difference between rotational motion and linear motion, explain this with the drawing.

A: Linear Motion - A rigid body consist of n particles will be in linear motion if all the particles…

Q: How the forced vibrations can arise?

A: When a body vibrates due to the influence of external periodic force, then this type of vibrations…

Q: 9. The top view shows a bend radius of the thin metal. Would a bend radius of 1/8" meet the…

A: If the bend radius lies with in the given range then it will meet the requirements. 18"=0.125" The…

Q: - Differentiate between engineering stress and true stress.

A: Stress: It is the ratio of the load applied on the body per unit area

Q: Examples for the applications of forces on curved surfaces.

Q: In a metal forming industry, you are assigned to setup an equipment which is required to reduce the…

A: To reduce the cross-section of a bar from 100x50mm into 75x25 mm various forming processes can be…

Q: epeat the above exercise for basic sheet metal working operations.

A: Sheet metal working process is discussed below

Q: The figure below shows a symmetric plane-strain upsetting process. The process may also be thought…

A: The intiallength of the tube is LiLi=2t+t =3tThe final length of the tube is LfLf=2t+2t…

Q: What is the linear variation in the shear strain?

A: The change in shape obtained due to shear stress is defined by shear strain.

Q: 7. Please analyze and compare the characteristics of sliding guide and rolling guide.

A: A linear guide (also known as a linear bearing) is a mechanical component that allows relative…

Q: Provide a precise definition of the cross-product. And give an explanation of how it relates to…

A: for solution refer below images.

Q: What is the linear variation in shear stress along any radial line?

A: For a linear-elastic material, the shear stress varies linearly with shear strain.

Q: DISCUSS THE SIGNIFICANCE OF DRAWING TO INDUSTRY.

A: Soln:- drawings are important because they are used to communicate the technical details of a…

Q: Differentiate ISOMETRIC DRAWING to OBLIQUE DRAWING.

Q: It is proposed to use an axisymmetric drawing operation to reduce the diameter of a cylindrical rod…

A: Calculated the minimum number of drawing stages needed to reduce diameter of cylinder from Do to…

Q: Before starting with the Teardown process, it is important to know: O The Purpose. The packaging. O…

A: Basics of Reverse Engineering.

Q: What is centripetal force?

A: Centripetal force is a force that acts during a circular motion. During circular motion centripetal…

Question

Please show your work. Thank you!

1. 1 kg of water (saturated mixture) is at 30C as shown below. The piston has a cross sec-
tional area of .0065 M^2 and a mass of 40kg. The piston is resting on the stops initially.
The total volume of the cylinder is 100 L and the atmospheric pressure is 94 kPa. Heat is
now added until the system becomes a saturated vapor. Assuming a gravitational con-
stant of 9.81 m/s^2, determine:
a. The temperature of the water when the piston first rises from the stops
b. The total work done by the water during this process
Patm
Stops
Vapor
Liquid

Expert Solution

Step 1

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Quality Assurance, Process Planning, and Quality Control

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

nQ2. Write short notes on Surface treatment process. List any two examples for Joining and assembly process.
Compare and contrast the differences between Paul Richer’s and Andrew Loomis’ concepts of proportions when drawing human characters. Explain your answer with some examples.
Prepare a report about the different types of defects in casting, rolling, extrusion and drawing products. Not less than printed three pages:
Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a) How much heat is generated? (b) What is the rise in temperature of the brass if 75% of the heat generated warms the brass? What happens to the other 25%? (don't change the hp, lb)
What are the three most common grips for drawing? Explain each type of grip, along with their advantages and shortcomings in different drawings. Provide some examples.
Q1. What is sheet metal working? Write any four products made through the sheet metal processing. Explain in detail about the galvanized iron and stainless steel sheet metal materials.
What are different types of drawing? Explain each with a help of neat sketch
2. a) With a neat diagram briefly explain the principle of Explosive Forming. b) Write any two applications of Explosive Forming.
what are t three components of shear strain?
Help
In one sentence, explain the difference between straightness and flatness.
If the wrought stock material costs $60 per kg, what is the lost value due to the material removed, assuming scrap is sold for $3 per kg? Assume the density of titanium is 4.5 g/cm3. Briefly explain how you got your answer. Neglect costs of lubricant/coolant, chip handling, etc. Round your answer down to the nearest dollar.