9) Three pillars, two of aluminium and one of steel support a rigid platform of 250 kN as shown in Fig. 8.39. If area of each aluminium pillar is 1200 mm2 and that of steel pillar is 1000 mm2, find the stresses developed in each pillar. Take Es = 2 x 105 N/mm2 and Ea 1 x 106 N/mm2. 250 kN LAI 091 - Aluminium 240 mm- Aluminium

9) Three pillars, two of aluminium and one of steel support a rigid platform of 250 kN as shown in Fig. 8.39. If area of each aluminium pillar is 1200 mm2 and that of steel pillar is 1000 mm2, find the stresses developed in each pillar. Take Es = 2 x 105 N/mm2 and Ea 1 x 106 N/mm2. 250 kN LAI 091 - Aluminium 240 mm- Aluminium

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
A simply supported girder spans 10 m. It carries two beams each at 3.5 m from the supports. The concentrated load from each beam is 70 kN
1. From the tabulation below determine if the column is safe to carry axial & bending load Yield stress of structural steel is 248 MPa. Modulus of elasticity is 200,000 MPa Service Load: Pl= Pd= assume K=1.0 Designation W8 x 28 W8 x 24 W8 x 21 W8 x 18 60 kN 100 KN Ag (mm2) 5323 4568 3974 2865 Weight/m d (depth) 42 bending moment Mux - Muy = 16 kN.m (LRFD load combination) bending moment Mx=My=12 kN.m (ASD load combination) L=3.6m flange Web 36 31 27 204.72 201.42 210.31 206.78 mm. width bf 165.99 164.97 133.86 133.35 thickness tf 11.81 10.16 10.16 8.38 thickness tw 7.24 6.22 6.35 5.84 Elastic Properties mm 4 mm 3 Ix x 106 Sxx 103 41 34 31 26 398 342 298 249 mm. rx 87.63 86.87 88.65 87.12 mm 4 lyx 106 9 8 4 3 mm 3 Sy x 106 109 92 61 50 mm ry 41.15 40.89 32 31.24 Plastic properties mm 3 Zx x 103 446 380 334 279 mm 3 Zy x 103 166 140 93 76 h=d-2k h 155.58 155.58 168.28 168.28
Strength of Materials II HOME WORK 1– Bending For the composite beam shown in the figure below, determine the maximum stresses in steel and aluminum, L = 2°Cuo+1o0) 200 mm 6 KN/m Al. 350 4200 mm Ilo mm |00 mm
Fundamental Deformable Bodies
A composite section consisting of steel and wood such as depicted. The cross section receives a bending moment M of 850 lb-ft. It is known that the modulus of elasticity of steel is 29000 ksi, while The modulus of elasticity of wood is 1600 ksi. Determine the maximum stress that occurs in each steel and wood parts
Strength of material
steel The hollow section column, shown in the figure below, has a length of 18 ft, and it is made of steel with a yield strength of 50 ksi. The column is fixed at the bottom and pinned at the top. What is the capacity of this column under a pure compressive loading? |3/4 in 3/4 in 10 in 5 in
value for modulus of elasticty for steel is 29000 ksi and for aluminum it is 10000ksi. yield strength for steel is 36 ksi and yield strength for aluminum is 37 ksi
Glu-laminated beams are used to support the roof and pulley load at a warehouse. Beams span 24 feet plus an eight foot overhang over the loading area. Determine the bending stress adequacy of the beam.