Q1: A concrete block of 40 KN weight is supported by three wires two of them are steel wires and middle one is aluminum wire. If the cross-sectional area of steel wire is 100 mm2 and that for aluminum is 200 mm2. Calculate the stresses in the aluminum and steel wires if EA for aluminum is 80 GPa and that for steel ES=200 GPa.

Q1: A concrete block of 40 KN weight is supported by three wires two of them are steel wires and middle one is aluminum wire. If the cross-sectional area of steel wire is 100 mm2 and that for aluminum is 200 mm2. Calculate the stresses in the aluminum and steel wires if EA for aluminum is 80 GPa and that for steel ES=200 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10/10 FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70 kN/MM2 100 kN RALU=30 MM Aluminum Steel 1m R ST 20 MM
The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 65°F. Compute the stress (ksi) in the Aluminum at 116 °F. Assume a = 6.5 x 10-6/° F for steel and 12.8 x 106/°F for aluminum Given: L1 = 15in; L2 = 11in Your final answer should contain two decimal places Steel A = 3 in² E = 29 x 106 psi Correct Answer: 3.92 L2 Aluminum A = 2 in² E = 10 x 106 psi L1
The following structure has a compression allowable stress of 50 MPa. In the laboratory, it was found that the allowable stress in tension is 5 MPa.
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d
An SSTM A36 strucural steel beam 3.6 m long is placed between two rigid supports when the temperature is 15 0C. What is the stress developed in the beam if the temperature rises to 50 0C? ___ MPa. Assume that the proportional limit is 235 MPa, and that lateral buckling is prevented. Calculate your answer to 1 decimal place.
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 73 GPa] bars, as shown. The beam is subjected to a bending moment of 445 N-m acting about the z axis. Using a = 15 mm, b = 125 mm, c = 30 mm, and d = 75 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum C Aluminum Answers: (a) Ogl Brass (b) Obr= i i b Brass a MPa MPa
Please help
asap please thank you
two decimal places
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
A composite beam is made of two brass [E = 112 GPa] bars bonded to two aluminum [E = 69 GPa] bars, as shown. The beam is subjected to a bending moment of 350 N-m acting about the z axis. Using a = 15 mm, b = 115 mm, c = 25 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum с Aluminum Answers: (a) Jal= (b) Obr= Brass i y i b Brass a a MPa MPa
COMPLETE SOLUTIONS PLEASE WITH FBD