Problem 8 only, solve carefully, include the units in every step and draw the diagram. Thanks! 8. What temperature will the rails just touched if steel railroad is 10 m long are laid with clearance of 3 mm at initialtemperature of 15 C. Use k = 11.7 x 104 m/m C. Also compute the strain and stress.9. A force tangent to 1 foot diameter pulley is 5 KN and is mounted on a 2 inches shaft. Determine the torsional deflectionif G = 83 x 10 Kpa.10.The pressure inside the cylindrical tank varies from 810 kpa to 3210 kpa continuously. The diameter of shell is 1.5 m.Find the following if yield point is 455 Mpa, endurance strength is 195 Mpa and factor of safety of 2.5.A. Wall thickness, mmB. The maximum stressC. The minimum stress

Given, L=10 mT1=15 Cα=11.7 x 10-6 Cδ=3 mm

Answered: 8. What temperature will the rails just…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm respectively, And the driver pulley runs at speed of 205 rpm. Find the speed at which is driven pulley runs in the machine. the speed of the driven pulley in rpm is
Please provide Handwritten answer. show all tge steps and FBD. thank you:)
7. A 4" diameter cylinder with a 1" diameter rod and a 12" stroke length needs to fully retract in 2 seconds with a working pressure of 85 psig. What is the required air flow rate?
(a) A turning operation is performed on a 660 mm cylindrical part of a certain alloy. The work material has a length of 140 mm as shown in Figure Q3-1. The finished (produced) part is shown in Figure Q3-2 which has an overall length of 100 mm. The remaining part of the raw material length is kept as a gripped part on the turning machine chuck. The cutting data is shown in Table Q3(a). Apply engineering calculations on the given metal cutting operations, Table Q3(a) Depth of cut Feed 2.5mm 0.15mm/rev Cutting Speed Rake angle The chip thickness after cut Shear strength 40m/min 50 0.17mm 280 MPa (i) Shear force. (ii) Coefficient of friction. e (iii) Cutting force. (iv) Time required to cut the part (v) Rate of material removal. 50mm $60mm -20mm 60 mm 140 mm 40 mm Figure Q3-1 Figure Q3-2 4 1 + DRG Ans Realm ? Ran x10*
PLease answer this question, Thank you very much
Sketch and explain any four Shaper operations?
In a lathe machine, The diameter of the driver and driven pulley are 2745 mm and 1200 mm respectively, And the driver pulley runs at speed of 225 rpm. Find the speed at which is driven pulley runs in the machine. the speed of the driven pulley in rpm is
Figure Q1 (a) and Figure Q1 (b) shows a C-shape block and rectangular hollow block respectively.
1. Name some uses of threads. Give an example of each. NOTE: Screw Thread – A screw thread may be visualized as a flexible form, like a piece of string that has been wrapped around a cylinder, or the sides of the cylindrical hole, at a uniform rate of advance, producing a form known as a helix. It may also be considered as a raised form produced on the outside of a cylinder, or on the inside walls of a cylindrical hole after a thread-cutting operation has been completed.
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
26. A JELLO IS sußJECTED TO %3D 0) DRAW THE DEFORMEO SHAPE CALCULATE ?
Steps please

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

8. What temperature will the rails just touched if steel railroad is 10 m long are laid with clearance of 3 mm at initial temperature of 15 C. Use k = 11.7 x 10 m/m C. Also compute the strain and stress.