8. Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [Ans. 51.7 mm]

8. Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [Ans. 51.7 mm]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 14 T=625 Nm Antriebszapfen 27 A F-5,31 KN 135 Zapfen der Getriebewelle 25 B 12,5 FB = =4,69 KN A…

A: It is stated in the above problem, that the stepped shaft is induced for bending and torsion…

Q: The cold-drawn steel shaft has an ultimate strength of 1350 MPa, yield strength of 1200 MPa, and…

Q: A steel shaft is 250mm long. It is subjected to a transverse bending load at its free end which…

A: Step 1: Step 2: Step 3: Step 4:

Q: In the figure below the shaft is simply supported in ball bearings at A and D. The shaft rotates and…

Q: L.

A: Given that, Torque, T=3100 N.mShear stress, τ=55 MPa, From torsion equation, TJ=τRJ=Polar moment of…

Q: 4) Compute the fatigue life of a rotating hub and shaft assembly, if at a critical point in the…

A: Step 1: Step 2: Step 3: Step 4:Step 5:Step 6:Step 7:

Q: Determine the factor of safety of the shaft. A 30-mm-diameter with a yield strength in tension of…

Q: A drive shaft is made of a hollow tube with an outer diameter of Do 2.5 in. It is desired to…

Q: QUESTION 2 In Figure 2, the shaft is made of a solid A992 steel at section AB (rs = 25 mm),…

Q: Required information A steel tube with a circular cross section has an outside diameter of 310 mm…

A: Steel tube with a circular cross section outside diameter D= 310 mm t= 2mm. length, L= 2 m torque,…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

Q: A metal hollow shaft is subject to a tensile load of 53kN and a positive torsional moment (right…

Q: a) A circular hollow shaft has an external diameter of 100mm and internal diameter of 80mm The…

Q: Q1 The rotating solid steel shaft is simply supported by bearings A and B, the gear has 500-mm pitch…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: The solid steel shaft loaded with T= 2 kN.m (cw) torque. if its diameter equal 6 centimeters and G=…

A: Given Data T=2 kN·mD=6 cmG=26 GPa Find Find the maximum shear stress.

Q: motor. The torque of the spindle is transferred to a wheat mill (not shown!) with the help of the…

Q: Here, on the third row, we have 0.577. How we got to this number?

A: For maximum distortion energy theory, Yield shear strength = 0.577 × Yield tensile strength

Q: hena) A hot-rolled steel shaft with a shoulder fillet is subjected to an axial load P which varies…

A: When a load or force is acting on an object in a way that it is parallel and on its axis then it is…

Q: TUEMS 4 Let's consider a solid orcular shaft subjected to the torque loads as shown Determine the…

A: Given:Yielding shear stress, ζy=100 MPafactor of safety, N=1.5

Q: cylindrical pressure vessel has inside diameter d_{o} = 500 mm and inside diameter di=490 mm.if it i…

A: Given Data Outside diameter of vessel is: do=500 mm Inside diameter iof vessel is:di=490 mm Factor…

Q: A solid steel shaft is subjected to torsional loadings. If T=10 kN-m. T= 45 MPa, the diameter of the…

Q: Based on Figure 1, analyze the state of stress at material element of point A on the cross section…

Q: The applied torque on shaft CD is T' = 95 N·m. The journal bearings B, C, and D allow free rotation…

Q: Estimate the shaft diameter required to produce a critical speed of rotation of 638 rpm for a steel…

Q: The composite shaft is subjected to the axial loads shown in (Figure 1). The diameters of ach…

A: given data;diameter(dAB)=19mmdiameter(dBC)=27mmdiameter(dCD)=13mmElasticity(Ecu)=126GPa=126*103MPa…

Q: Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces applied…

A: The given question is related to the combined bending and torsion, there are simultaneous loads…

Q: The shaft shown is machined from C1040, OQT (oil-quenched treatment) @ 1,000°F. It is subjected to a…

Q: 42, The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find…

A: Given: The static deflection of shaft, x= 0.36 mm

Q: Part A For a hard aluminum notched part having notch dimension r = 0.75 in, geometric…

A: Given data: notch dimension r=0.75 ingeometric stress concentration factor Kt=2.8material strength…

Q: Q1: Shaft subjected to the loadings in phase shown such that: T=0 N.m to 200 N.m M=-200 to 200 N.m…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

8. Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and
yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect
stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken
as 1.5.
[Ans. 51.7 mm]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
B) A simply supported shaft is shown in the following Figure. A constant magnitude distributed unit load p is applied as the shaft rotates. The shaft is also subject to a steady torque of Tmax 2000-N -m., find the diameter of shaft required to obtain a safety factor of 2.5 in fatigue loading if the shaft is steel of Sut 814 MPa and Sy 703 MPa. The dimensions are in cm, the distributed force in N/cm, and the torque is in N-m. No stress concentrations are present, the shaft is machined, the required reliability is 90%, and the shaft operates at room temperature Figure: 1= 20-cm: b = 18-cm ; a = 16 cm Applied distributed load p:= 1000 N em ; 区区

Please Explain How you Get Kt? What's d=40 there? Sut=800MPa by machining method in the figure, Shaft variable M made of a steel with Sy3640MPa subjected to moments. 50% confidence status n=2 safety according to Goodman fatigue damage criterion for the maximum moment M to be applied to the shaft. find it. 5-mm rad. 4M 4M 60 mm 50 mm M M
• Compute the maximum shear stress and angle of twist of each type of shaft below. – Closed tube shaft – Open tube shaft • Briefly describe which type of shaft is more effective. • See the dimensions of each tube, the value of internal torque, and the shear modulus in the next page.
Find the diameter of a shaft made of (37 Mn 2 steel) having the ultimate tensile strength as (600 MPa) and yield stress as (440 MPa). The shaft is subjected to completely reversed axial load of (200 kN). Neglect stress concentration factor and assume surface finish factor as (0.8). The factor of safety may be taken as (1.5). (After the diameter was found, correct it for the actual size factor). mechanical design pls solve fast
Problem 5 only, solve carefully, include the units in every step and draw the diagram. Thanks! A hollow shaft transmits 10 kW and running at 650 rpm with a shearing stress of 55 Mpa. The outside diameter is 1.2times that of the inside diameter. Find the inside and outside diameters in mm.
Fill in the blanks: Find the size of wire in mm if the maximum design stress is 425 000 KPa. A mass 72.40022026 kg falls from a height of 0.85 m to the center of a horizontal platform mounted on five helical springs. At impact each springs deflects 65 mm. Assume spring index of 8.
Please present drawings/FBD’s illustrating your solution.
Problem 3: A hot rolled steel shaft is subjected to a torsional load that varies from 3000 in-lb clockwise to 1000 in-lb counterclockwise as an applied bending moment at a critical section varies from + 4000 in-lb to 2000 in-lb. The shaft is of uniform cross section and no keyway is present at the critical sec- tion. Determine the required shaft diameter. The material has an ultimate strength of 80,000 psi and a yield strength of 60,000 psi. Base design on a factor of safety N=1.5. Take the endurance limit as half the ultimate strength.
Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a torque of 1200 Nm. Since the shear strength for the shaft material is 40 MPa, the maximum allowable unit torsion angle of the bar is 0.75 ^ 0 / m and the shear modulus of steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outside diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and weight ratio for ring cross section and solid section shafts
The static shaft shown below is machined from aluminum 6082-T6. It is subjected to a static force of P=20 kN, T1=50 Nm, T2=50 Nm (Assume there is no buckling, Sut=240 Mpa, oy= 200 Mpa, E=70 Gpa). a) Find out the factor of safety using appropriate failure criteria. b) Determine the critical point(s) of the shaft -100 mm T2 d=20 mm P. T1
(8) An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r = 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). 6" (a) At the fillet, compute D and the 30 maximum tensile stress. (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?