8-48 A vertical channel 152 x 76 (see Table A-7) has a cantilever beam bolted to it as shown. The channel is hot-rolled AISI 1006 steel. The bar is of hot-rolled AISI 1015 steel. The shoulder bolts are M12 x 1.75 ISO 5.8. For a design factor of 2.8, find the safe force F that can be applied to the cantilever. 12 Problem 8-48 Dimensions in millimeters. %24 50 -50--50-- 125

8-48 A vertical channel 152 x 76 (see Table A-7) has a cantilever beam bolted to it as shown. The channel is hot-rolled AISI 1006 steel. The bar is of hot-rolled AISI 1015 steel. The shoulder bolts are M12 x 1.75 ISO 5.8. For a design factor of 2.8, find the safe force F that can be applied to the cantilever. 12 Problem 8-48 Dimensions in millimeters. %24 50 -50--50-- 125

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side. For the steel countershaft shown in the figure below, find the deflection and slope of the shaft at point A. Use superposition with the deflection equations in Table A-9. Assume the bearings constitute simple supports. In the figure shown below, Tx= 330 lbf, Ty= 50 lbf, and the diameter of the shaft (dshaft) = 1.07 in. y Tx dshaft 6 dia. Ty 8 dia. The deflection at point A is The slope at point A is rad. in.
Pls give right answer with step by step explanation. Design a clamp coupling for a shaft diameter of 60 mm. The torsional moment to be transmitted by this coupling taking in to account over loading as 160 N-m. The number of bolts used are 6 and the allowable stress in the material of the bolt is limited to 5N / m * m ^ 2 . The coefficient of friction between the shaft and muff material is 0.25.
The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for nonpermanent assembly. The stiffnesses have already been computed and are kp=4 Mlb/in and km = 16 Mlb/in. Laad line F. Steady stress (a) Assuming that the bolts, rather than the welds, govern the strength of this design, determine the safe repeated load that can be imposed on this assembly using the Goodman criterion with the load line in the Figure and a fatigue design factor of 2. (b) Compute the static load factors based on the load found in part (a). (ie. Yielding factor of safety, Load factor of safety and factor against joint separation)
The beam below is subjected to a sinusoidal forcing function with Fmax = F and Fmin -F/2 where l 40 mm. The cross section is a rectangular with thickness (t) and height (h). The beam is in room temperature, it is ground, it is 90% reliable. Find the stress state in the beam due to this loading. choose the type of steel that will give a safety factor of 3 for N=5E8 cycles using Goodman. 1 т, а — 0.4 т, b %3D 0.6 т, F 500 N,I %3D 2.85Е — 08 m*, h - b |R1 R2
The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the gear on the shaft is 0.9 kg, dimension, surface and notch factors KbK / Kç = 0.83, shaft speed n = 1120 rpm, shaft transmitted power 7.5 kW, force on shaft Fn = F = 2680 N Since the desired safety coefficient is Ssafe = 2; Draw the bending and torsional moment diagrams of the shaft.
Problem 8-20. Calculate the deflection of the ring along the load line shown in Fig. 8-13 by taking E= 200 GN/m².
The figure shows a round shaft from a gear transmission. Gears are mounted at points A, C, and E. Supporting bearings are at B and D. The forces transmitted from the gears to the shaft are shown, all acting downward. Compute the maximum stress due to bending in the shaft, accounting for stress concentrations. Draw shear diagram and moment diagram. calculate the safety factor for the material selected. The material is 4150 OQT 1300. Assume that f1 = 9.5 KN , f2= 13.5 KN and f3 =18 KN
can you answer this question
Q3 The figure shows a round shaft from a gear transmission. Gears are mounted at points A, C, and E. Supporting bearings are at B and D. The forces transmitted from the gears to the shaft are shown, all acting downward. Compute the maximum stress due to bending in the shaft, accounting for stress concentrations. calculate the safety factor for the material selected.if martial 4150 OQT 1300 force 1 (f1)=9.5 kn ,Force 2(f2)=13.5Kn ,Force3 (f3)=18Kn
A radial ball bearing is assembled on a steel shaft of 30 mm diameter with a transition fit, as shown in the figure. 1. Suggest a suitable transition fit then calculate the limit sizes of shaft and hole. 2. Calculate the maximum interference and the maximum clearance for the suggested transition fit. Ball bearing Steel shaft (D = 30 mm)