7.25 The steel pipe AB has a 102-mm outer diameter and a 6-mm wall thickness. Knowing that arm CD is rigidly attached to the pipe, determine the principal stresses and the maximum shearing stress at point K. 10 kN 200 mm C Fig. P7.25 6 mm B H A D 51 mm 150 mm X

7.25 The steel pipe AB has a 102-mm outer diameter and a 6-mm wall thickness. Knowing that arm CD is rigidly attached to the pipe, determine the principal stresses and the maximum shearing stress at point K. 10 kN 200 mm C Fig. P7.25 6 mm B H A D 51 mm 150 mm X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two members of uniform cross section 50 *80 mm are glued together along plane a–a that forms an…

A: Draw the stress element of the cross-section.

Q: the bar shown is subjected to uniform tensile stresses along the x and y axes of a magnitude 676…

A: Given Data Stress in x direction, 676MPa Stress in y-direction, 676 MPa Modulus of elasticity,…

Q: 7.118 For the tank of Prob. 7.117, determine the largest allowable gage pressure, knowing that the…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: A 1-in. square (thickness 0.12-in) plate was subjected to a uniform load of 0.72 kip/in in the…

A: Givensquare platea=1int=0.12inFx=0.72 kip/inFy=1.44 kip/inE=29×106 psiv=0.3

Q: The forces ar applied to the bar shown. Determine the normal and shearing stresses at (a) point a,…

Q: nd P7.11 40 MPa The grain of a wooden member forms an angle of 15° with the vertical. For the state…

A: The shear stress

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: ogeth le of 25° with the horizontal. Knowing that the allowable str 0 kPa and t = 600 kPa, determine…

Q: Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness…

A: Given Force, F = 6 kips Thickness, t = 0.8 in Find Normal stress at points a and f

Q: A steel shaft of diameter 50 mm and length 1.2 m (E = 210 GPa and v = 0.3) is loaded with multiple…

Q: Problem 8.5 A circular ring is subjected to a pull of 15 kN. The ring is of T-section as shown in…

A: A circular ring is known to be exposed to a 15 kN pull.The ring has a T-section, and the internal…

Q: 9. The compressed air vessel has a radius of 42 cm and a uniform wall thickness of 5 82 cm mm.…

Q: Load P is applied to a steel rod supported as shown by an aluminum plate into which a…

Q: 2.5 ksi 4 ksi 5 ksi

Q: A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal…

A: Given: Length of side AB = 4 in Length of side BC = 3 in To find: change in length of (a) side AB,…

Q: Problem 4 The steel pipe AB has a 102-mam outer diameter and a 6-mm wall thickness. Knowing that arm…

Q: A load of 7,000 N acts on the machine part shown in Fig. 5a. The machine par thickness of 15 mm…

Q: Link BD consists of a single wooden member 38 mm wide and 19.2 mm thick. Knowing that each pin has a…

A: Width of link BD, b= 38 mm Thickness of link BD, t= 19.2 mm Diameter of the pin, d= 14.30 mm θ= 0∘…

Q: An impeller mechanism in a granular material mixing tank is shown. The shaft is hollow with a 2.25"…

A: Given, ro = 2.25" θmax=6o τmax=10 ksi G = 11000 ksi

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

Q: For the state of stress shown, it is known that the normal and shearing stresses are directed as…

A: Given Data: The stress in x-direction is σx=14 ksi. The stress in y-direction is σy=9 ksi. The…

Q: 19. knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) the…

A: Diagram

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: The centric force P is applied to a short post as shown. Knowing that the stresses on plane a–a are…

A: Given data as per the question σ=215 ksi τ= 5 ksi cosβ=ADEADFADF=ADEcosβADF=ADEsecβforce acting on…

Q: ortion of that link when (a) 0=0°, (b) 0–90°. -12 in- 2 in. S in

Q: 6. 13 The beam carries a concentrated load F and a uniformly distributed load that tou 4F. Determine…

Q: Why is the net area for AB (0.045-0.0102) * (0.012) ? Why is AB in tension and BC in compression

Q: T C. | I I Η Κ 10 kN 240 mm

Q: Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness…

A: given data force = 6 kips. thickness of bar = 0.8 in depth of beam =3 in find the combined at stress…

Q: diameter cast-iron post ABD. At point H, determine (a) the principal stresses and principal planes,…

A: GIVEN :- F=13 KNd=60mmTO FIND :-a) the principal stresses and principal planesb) the maximum…

Q: Problem 2. Three loads are applied to the short sectional dimensions of the post are shown in Fig…

Q: The assembly shown below is subjected to the load P applied at 30°. The cylindrical pins at A, B, C,…

Q: wo wooden boards, measuring 15 mm thick and 225 mm wide, are joined by the socket joint shown.…

Q: A rod must not stretch more than 6 mm when the tension in the wire is 8 kN. Knowing that E = 105…

Q: A steel shaft (G=77 GPa) & an (Al) tube (G = 27 GPa) are connected to a fixed support & a rigid disk…

A: Given: Steel shaft d =50mm τallow = 120 MPa Js =(π/32)*d4…

Q: THE FRAME SHOWN CONSISTS OF FOUR WOODEN MEMBERS, ABC, DEF,BE, AND CF. KNOWING THAT EACH MEMBER HAS A…

Q: the bar shown is subjected if the length a = 584 mm a if the modulus of elasticity then, its new…

A: Any action that can change the state of motion is called force, Force is described by its magnitude,…

Q: Problem 08.043 Determine principal stresses in a shaft under combined loadings. The steel pipe AB…

Q: Problem 8-12 A bar of rectangular cross-section, with a width of 60 mm and a thickness of 40 mm, is…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

7.25 The steel pipe AB has a 102-mm outer diameter and a 6-mm wall
thickness. Knowing that arm CD is rigidly attached to the pipe,
determine the principal stresses and the maximum shearing stress
at point K.
10 kN
200 mm
C
Fig. P7.25
22
6 mm
B
H
D
51 mm
150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

7.6666
A chain block is hanged on a pin which is supported by plates on both side as shown. If the maximum safe load capacity is 3000 lb, determine (a) the shearing stress on the shaft having a diameter of 1.75 in. (b) and the thickness of the plates if the bearing stress on the plates is 20% greater than the shearing stress.
The compressed-air tank AB has a 250-mm outside diameter and an 8-mm wall thickness. It is fitted with a collar by which a 40-kN force P is applied at B in the horizontal direction. Knowing that the gage pressure inside the tank is 5 MPa, determine the maximum normal stress and the maximum shearing stress at point K. (Round the final answers to one decimal place.)
Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness of the element is 0.8 in., determine the combined normal stresses at points (a) and (f). 1.5 in. 1.5 in. B a ob С 8 in. □e 0 f 8 in. 6 kips 35° 8 in.
Question 3. A 4 by 4-in. wood-post BC is connected to a 1-in. diameter steel eye-bar AB to form a hoist. A load of w = 7000 Ibs is applied at point B on the hoist. (a)Determine the axial stresses in members AB and BC. (b) Determine the cross shearing stress in the 1-in. diameter bolt at point A. STEEL V -7000 lb WOOD FIG. I A
w=15
Please show intermediate steps including free body diagrams, equations used, problem setup etc. so that your approach can be followed
SECTION B(1) Question 1 The bell crank CBA is connected to a pin support B in double shear with 8-mm diameter pin B and to the 10-mm diameter rod CD. Knowing that the ultimate shearing stress is 110 MPa for the steel used in pin B and the ultimate normal stress is 230 MPa for the steel used in rod CD. Determine the maximum vertical force P that can be applied if an overall factor of safety of 1.5 is desired. 45% 300 mm B Figure 1 -450 mm-
3. A solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross- sectional area of 150 mm x 310 mm to the median line of the cross-section. (a) Determine the required thickness of the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar. (b) Determine the shear stress in the tube . If it is subjected to a torque T = 15 kN-m and a thickness of 10 mm. and (c) Determine the angle of twist in degrees of the tube if the length of the tube is 1000 mm and the shear modulus is 75 GPa. Thickness of the tube is 10 mm and the torque T = 15 kN-m.
The extruded cross section is subjected to a shear force of V = 495 N. Dimensions of the cross section are b = 42 mm, d = 75 mm, and t = 3.0 mm. Determine: (a) the value of Q associated with point H, located at a = 13 mm above the lower surface of the cross section. (b) the magnitude of the horizontal shear stress at point H. (c) the magnitude of the maximum horizontal shear stress in the cross section. ((уp) H a b Answer: (a) QH = 6306 mm3 (b) TH = i 1.091744397 kPa (c) Tmax = 1.637227058 kPa
A spherical gas container having an outer diameter of 5 m and a wall thickness of 22 mm is made of a steel for which E=200 GPa and v =0.29. Knowing that the gage pressure in the container is increased from zero to 1.7 MPa, determine (a) the maximum normal stress in the container, (b) the increase in the diameter of the container
7.58 For the state of stress shown, determine the range of values of 0 for which the normal stress o, is equal to or less than 100 MPa. 90 MPa Try 60 MPa the Fig. P7.58 and P7.59