Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness of the element is 0.8 in., determine the combined normal stresses at points (a) and (f). 1.5 in. 1.5 in. B a ob C 8 in. De 0 f 8 in. 6 kips 35° 8 in.

Q: Ex : Two solid cylindrical rods AB and BC are welded together at B and loaded as shown , Knowing…

A:

Q: Q1 The curved portion of the bar shown has an inner radius of 20 mm. Knowing that the allowable…

A: Given,

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the internal…

A:

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question  Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: Problem 4 The steel pipe AB has a 102-mam outer diameter and a 6-mm wall thickness. Knowing that arm…

A:

Q: Link BD consists of a single wooden member 38.2 mm wide and 20.4 mm thick. Knowing that each pin has…

A:

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A:

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and = loaded as shown. Knowing…

A: Given P = 10 kips To find Average normal stress

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: Draw Mohr's circle that describes each of the following states of stress.

A: Given data:- σx =-8 ksi σy =12 ksi τxv=-6 ksi To draw:- Mohrs circle

Q: B The two rods AB and AC have diameters of 10 millimeters and 8 millimeters. Determine largest…

A:

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: Why is the net area for AB (0.045-0.0102) * (0.012) ? Why is AB in tension and BC in compression

A:

Q: 6 in. ااه 800 lb

A:

Q: B

A: Given DataHorizontal force at end D of the lever, P=150 lbThe diameter of portion AB of the lever,…

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: Problem 2. Three loads are applied to the short sectional dimensions of the post are shown in Fig…

A:

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.