T C. | I I Η Κ 10 kN 240 mm

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: A couple of magnitude M is applied to a square bar of side a. For each of the orientations shown,…

A: Given that: The edge of square cross section is: a.   The bending moment equation is given as:…

Q: For the given state of plane stress in the r-y plane, determine (a) the maximum in-plane shear…

A:

Q: Determine the principal stresses and the absolute maximum shear stress. 2.5 ksi 4 ksi 5 ksi

A:

Q: the normal and shearing

A: To determine the normal and shear stress .

Q: The internal loadings at a cross section through the shaft consist of an axial force of 1500 kN, a…

A: Given: axial force, P =1500KN Bending moment, M =40KNm Torsional moment, T =40KNm radius of shaft,r…

Q: с 1 ft 2 ft B 150 lb-ft/ft A 2 ft A copper pipe is tightly secured to the wall at C and a uniformly…

A:

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: The forces ar applied to the bar shown. Determine the normal and shearing stresses at (a) point a,…

A:

Q: Determine the principal stresses and the absolute maximum shear stress.

A:

Q: The rectangular bar has a width of w = 3.00 in. and a thickness of t = 2.00 in. The normal stress on…

A: (a) The magnitude of load P is 59.04 kips. (b) The shear stress on plane AB is 4.8 ksi. (c) The…

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question  Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: Determine the state of stress at point A of the rectangular post shown loaded with concentrated…

A: Ffgg

Q: orce of P₂ = 610 N is exerted on control arm BC, which is securely attached to the solid 39 mm…

A:

Q: Three forces, each of magnitude P = 3 kN, are applied to the structure shown. Determine the…

A: Solution.jpg

Q: N THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A AND…

A:

Q: 30 mm and 40 mm, respectively. Determine the principal stresses and

A:

Q: Determine the shearing stress acting at joint C with a pin diameter d of 46 mm if a vertical force…

A: Givend=46mmF=24 kNAAB=0.006 m2ABC=0.005 m2AC=y=8.7 mAB=x=10m

Q: A 1000 kg homogenous bar 2 m long is suspended horizontally from  two vertical cables A and B each…

A: Given Datam=1000kgA=400m2σA=100MPaσB=50MPa I had Given Required figure

Q: The following shaft is free at A and connected to a fixed support at C. The shaft has a solid…

A: For solution refer below images.

Q: The beam supports the loading shown. Determine the state of stress at points E and F at section a-a.

A:

Q: The steel tube below has an inside diameter of 2.75”, and an outside diameter of 3”. If the tube is…

A: The polar moment of inertia of the bar can be determined as,

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kNforce is applied to the…

A:

Q: a force q of magnitude 3kips is applied to machine element ab. the uniform thickness of the element…

A: Given data Force (Q) = 3 Kips Thickness (t) = 0.8 in

Q: 9-74 If the box wrench is subjected to the 50 lb force, determine the principal stresses and maximum…

A:

Q: 1.4 kNm C H KI 10 kN 240

A:

Q: A load of 7,000 N acts on the machine part shown in Fig. 5a. The machine par thickness of 15 mm…

A:

Q: The extruded plastic shape will be subjected to an internal shear force of V = 380 lb. Dimensions…

A:

Q: 14 mm diameter rivet joins the plates that are each 1.10 m wide. The allowable stresses are 120 000…

A:

Q: 5 in. 2. Two wooden members of uniform rectangular cross section are joined by a glued scarf splice…

A:

Q: The stress acting on two planes at a point is indicated. Determine the shear stress on plane a–a and…

A: The component of 60 ksi in horizontal direction,   σx=60 ksisin60°=51.96 ksi The component of 60 ksi…

Q: The extruded plastic shape will be subjected to an internal shear force of V= 380 Ib. Dimensions of…

A:

Q: The extruded plastic shape will be subjected to an internal shear force of V- 385 lb. Dimensions of…

A:

Q: Determine the principal planes and the principal stresses for the state of plane stress resulting…

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.