7. The following table relates to the open-circuit curve of a shunt gen-Determine the no-load terminal voltage if the field circuit resistanceIf the speed is now halved, what is the resultant terminal voltage?erator running at 750 rev/min:Generated voltage (V)Field current (A)10 172 300 360 385 3950 1 2 34 5is 125 2.At the reduced speed, what valne of field circuit resistance will give ano-load terminal voltage of 175 V?(N.C.T.E.C., O.2)diti

Answered: Image /qna-images/answer/d0d2213e-6c3e-4c19-98f4-0ca37c6b7793.jpg

7. The following table relates to the open-circuit curve of a shunt erator running at 750 rev/min: Generated voltage (V) Field current (A) 172 300 360 385 395 4 5 10 0 1 2 3 Determine the no-load terminal voltage if the field circuit resistance If the speed is now halved, what is the resultant terminal voltage? is 125 Q. At the reduced speed, what valus of field circuit resistance will give a no-load terminal voltage of 175 V? (N.C.T.E.C., 0.2)

7. The following table relates to the open-circuit curve of a shunt erator running at 750 rev/min: Generated voltage (V) Field current (A) 172 300 360 385 395 4 5 10 0 1 2 3 Determine the no-load terminal voltage if the field circuit resistance If the speed is now halved, what is the resultant terminal voltage? is 125 Q. At the reduced speed, what valus of field circuit resistance will give a no-load terminal voltage of 175 V? (N.C.T.E.C., 0.2)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q27/ (a) With necessary diagram, explain the working principle of dc motor
A250 V, dc shunt motar has an armeture resistance of 0.5 chmand a field resistance of 250 chm When driving a load of constant torque at 600 r.pm, the amature current is 20 A If it is desired to raise the speed from600 to 800 r.pm, what resistance should be inserted in the shunt field circut? Assume that the megnetic circut is unsaturated
power electronics and drives
3. Find the transfer function, 0,(s)/E,(s), for the motor and load shown in the figure below. The torque-speed curve is given by Tm = -8awm + 200 when the input voltage is 100 volts. edt) Motor | N = 20 N2 = 100 N3= 25 Ja = 1 kg-m? Da = 5 N-m-s/rad DL = 800 N-m-s/rad N4 = 100 J = 400 kg-m²
what is the best switch for buck boost converter and why
A 250 V shunt motor, having an armature resistance of 0.2 ohm draws fromthe mains a current of 50 A on half full load. The speed is to beincreased to twice half full load speed. If the torque of the motor is ofconstant magnitude, determine the percentage change in flux required.[Ans. 52.29] I WANT A DIFFRENT APPROACH (NOT COPY PASTE ON LIBRARY)
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If the motor speed is reduced to 50% of the rated speed (1200rpm), find the inductive voltage, the induced current, the motor efficiency and the motor speed at no load to obtain the rated torque at this speed. (Field supply current will be considered constant). I A V V Eff % ONL rpm
A Flyback converter (for questions 1-3) shown below has the following parameters. Vin-100V, Vo-20v, Po-40W, D-0.25, Fsw-250kHz 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. NI: N2 - 5: 3 B. NI: N2 - 3:5 C. NI: N2- 5:2 D. None of the above
A 110-V, 1-phase, 4-pole, 60-Hz induction motor has the following circuit constants: R1 = R2’ = 1.6 ohm,X1 = X2’ = 1.8 ohm, Xm = 60 ohm; core loss is 16 W and friction and windage loss is 12 W. Determine theefficiency of the motor at 0.04 slip by using (a) the exact equivalent circuit and (b) the approximateequivalent circuit
7. The following table relates to the open-circuit curve of a shunt gen- erator running at 750 rev/min: 10 172 300 360 385 395 Generated voltage (V) Field current (A) 0 1 2 3 4 5 Determine the no-load terminal voltage if the field circuit resistance is 125 Q. If the speed is now halved, what is the resultant terminal voltage? At the reduced speed, what value of field circuit resistance will give a no-load terminal voltage of 175 V? (N.C.T.E.C., O.2)
power electronics and drives
3. A factory's separately excited DC generator has an armature resistance of 0.252. The machine is driven at 1000 revolutions per minute giving the following data: E,[V] I[A] a) Plot the open circuit characteristic when the machine is driven at 1000 and at 1500 rev/min. b) If the machine is drive at 1500 rev/min and its field current is adjusted to 0.2 A, plot the output voltage (in the same axis with (a)) as the load current is varied from 0 to 40A. For a full load current of 40A, what is the voltage regulation? 5 28 75 112 132 150 0.1 0.3 0.5 0.7 0.9