A Flyback converter (for questions 1-3) shown below has the following parameters. Vin=100V, Vo=20v,Po=40W, D=0.25, Fsw=250kHziini outin1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding?A. Ν1: N25:3B. N1: N2 = 3:5C. N1: N2= 5:2D. None of the above%3D2. What is the maximum voltage on the power switch?A. 120VВ. 133VС. 100VD. None of the above3. What is the maximum voltage on the diode?Α. 40VВ. 133VC. 80VD. None of the above4. The magnetizing inductor at the primary side winding is 100uH, what is the peak current in the powerswitch?Α. 1.8ΑВ. 1.6AС. 2.1AD. None of the above

Note: As per our policy, I have attempted the first three questions. Given data: Vin=100 VVo=20…

A Flyback converter (for questions 1-3) shown below has the following parameters. Vin=100V, Vo=20V, Po=40W, D=0.25, Fsw=250kHz in iout 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. N1: N2 = 5: 3 B. N1: N2 = 3:5 C. N1: N2= 5:2 D. None of the above 2. What is the maximum voltage on the power switch? A. 120V В. 133V C. 100V D. None of the above 3. What is the maximum voltage on the diode? A. 40V В. 133V С. 80V D. None of the above 4. The magnetizing inductor at the primary side winding is 100uH, what is the peak current in the power switch? A. 1.8Α В. 1.6A С. 2.1A D. None of the above

A Flyback converter (for questions 1-3) shown below has the following parameters. Vin=100V, Vo=20V, Po=40W, D=0.25, Fsw=250kHz in iout 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. N1: N2 = 5: 3 B. N1: N2 = 3:5 C. N1: N2= 5:2 D. None of the above 2. What is the maximum voltage on the power switch? A. 120V В. 133V C. 100V D. None of the above 3. What is the maximum voltage on the diode? A. 40V В. 133V С. 80V D. None of the above 4. The magnetizing inductor at the primary side winding is 100uH, what is the peak current in the power switch? A. 1.8Α В. 1.6A С. 2.1A D. None of the above

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer all subparts. I will really upvote
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
Comment briefly on the relationship between input and output power at varying excitation levels and on the relationship between excitation and power factor or reactive power, when the synchronous machine is connected to an infinite busbar
5. The single phase full wave AC voltage controller operates on a single phase supply voltage of maximum voltage as 230 V, at 50 Hz. If the triac is triggered at a delay angle of 45°, during each half cycle of input supply. Find the rms output voltage, input power factor and the power in the load. 6. A voltage source v= 100 sin 377t supplies a resistive load of 100 2 through a pair of back to back connected thyristor (ac regulator). Calculate the power in the load, if the thyristor firing angle is 2n/3 with respect to the supply voltage.
A trapezoidal BLDC motor has an armature resistance of 0.6 Ω phase and the voltage drop across conducting transistor is 0.6 V. Motor is operated in the bipolar mode. This motor runs at 2000 rev/m on no load drawing negligible current from 200 V DC input. at what speed the motor run when loaded to 5 Nm torque.to what value should the input voltage be reduced to lower the speed to 500 rev/m for the same torque.
Q6: Three phase full- convertor, connected to high inductive load 100 .If the Input supply is three phase star 208V find: a. The output load current at firing angle 40 b. Power consumed from the supply(P.) c. For the current above if the firing angle change to 135, calculate the restored power.
What are the advantages and disadvantages of using Flyback and Push-Pull Converters in electrical power applications?
A 550 volts, 55KVA single phase alternator has an effective resistance of 0.02 ohms, a fieldresistance of 10 ohms produces an armature current of 200 A on short circuit and an EMF of 450volts on open circuit. What is the voltage regulation at full load and 0.80 lagging power factor
5-The frequency of oscillation is maximum for a. underdamped system b. overdamped system c. undamped system d. critically damped system
13/ The Squirrel cage induction motor has high efficiency. Select one: True False
urgent please no need to explanation
H.W: Write a short report about using internet of things (loT) in speed control of a three- phase induction Motor. THREE PHASI INDUCTION MOTOR BRIDXGE POWER TRANSFORMER RECTIFIER WITH FILTER THREE PHASE INVERTER DRIVER DRIVER CIRCUIT TRANSPORMER SPEED FEEDBACK POWER SUPPLY ARDUINO CONTROLLER NODE MCU POWER SUPPLY 0-0-0-0-0