A250 V, dc shunt motar has an armeture resistance of 0.5 chmand a field resistanceof 250 chm When driving a load of constant torque at 600 r.pm, the amature currentis 20 A If it is desired to raise the speed from600 to 800 r.pm, what resistance shouldbe inserted in the shunt field circut? Assume that the megnetic circut is unsaturated

Answered: Image /qna-images/answer/9a17d4fa-2c26-4b39-8a4c-d7f33690133f.jpg

A250 V, dc shunt matar has an ameture resistance of 0.5 chmand a field resistance of 250 chm When driving a load of canstant torque at 600 r.pm, the armature current is 20 A If it is desired to raise the speed fram600 to 800 r.pm, what resistance should be inserted in the shunt field circut? Assume that the magnetic circut is unsaturated

A250 V, dc shunt matar has an ameture resistance of 0.5 chmand a field resistance of 250 chm When driving a load of canstant torque at 600 r.pm, the armature current is 20 A If it is desired to raise the speed fram600 to 800 r.pm, what resistance should be inserted in the shunt field circut? Assume that the magnetic circut is unsaturated

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An 8 pole, lap-wound armature has 1200 conductors and a flux pole is 0.06wb. Determine the emf generated when the dc machine running at 600 rev/min.(CLO2)
A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with rotating speed of 1000rpm. The armature is wave-wound and has 500 conductors. The useful flux per pole is 0.03Wb and there are 4 poles (2 pairs of poles). The armature resistance is 0.4 Ohms. Calculate: 1.The internal emf of the motor. 2.The armature current. CLEAR AND CORRECT OR DISLIKE
• Q5/ in a DC motor. List and describe the types of losses that occur
A 220 V , 60 Hz , supply is connected to 200 – turn armature winding of reluctance 1.7x105 At / Wb . Find the magnetizing reactance , the rms values of the ( magneto – motive force , exciting and armature currents , magnetic flux ) , and the inductance Draw the phasor diagram of the circuit .
Q4) What is the effect in series motor if you assume V = Eb , with low resistance fielding winding ? a) b) The given information about series motor on full – load (with that the flux is proportional to the field current) is a ) takes ( 78A) and runs at (850 r.p.m) , the series winding resistance is (0.04 2) , with diverter in parallel with the field winding is a (0.18 2) and the armature resistance is (0.09 S2). ( 220 V Neglected the iron, friction and windage losses. Determine the efficiency , speed when developing full load torque ,the maximum efficiency .
A 240 V series motor develops a torque of 120 Nm at a speed of 900 rpm. The armature winding resistance is 0.20 and the series field winding resistance is 0.1 Q. For a constant load torque find the new speed of the motor when a diverter resistance of 0.1 Q is placed across the series field winding.
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
For a 4-pole dc armature with 28 slots and 8 coil-sides per slot, find the winding pitches and the commutator pitch for a wave winding. What is the distance between brushes in terms of commutator segments?