6. The following engineering stress-strain data were obtained for 0.2% C plain carbon steel. (a) Plot the engineering stress-strain curve (b) Determine the ultimate tensile strength for the alloy (c) Determine the percent elongation at fracture (d) Plot the true stress-strain curve Engineering strain, in./in. Engineering stress, ksi 30 0.001 55 0.002 60 0.005 68 0.01 72 0.02 74 0.04 75 0.06 76 0.08 75 0.1 73 0.12 69 0.14 65 0.16 56 0.18 51 0.19(fracture) LO o o LO o o o

6. The following engineering stress-strain data were obtained for 0.2% C plain carbon steel. (a) Plot the engineering stress-strain curve (b) Determine the ultimate tensile strength for the alloy (c) Determine the percent elongation at fracture (d) Plot the true stress-strain curve Engineering strain, in./in. Engineering stress, ksi 30 0.001 55 0.002 60 0.005 68 0.01 72 0.02 74 0.04 75 0.06 76 0.08 75 0.1 73 0.12 69 0.14 65 0.16 56 0.18 51 0.19(fracture) LO o o LO o o o

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

70% + | 8 0 4. An application requires ultimate tensile strength and yield strength of a steel at 110 ksi and 91 ksi, respectively. A data table is attached in the back of the test. Answer the following 4 questions: 4.1. Can SAE 1040 steel be selected for this application? 4.2. If "no" is the answer in Part I, the following Part II, III, and IV can be ignored. If "yes" is the answer in Part I, which condition of SAE 1040 should be selected? 4.3. Why is that steel with the condition in part II selected? 4.4. Is the selected steel brittle or ductile? and Why? Page 4 of 6
Ql- mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram and determine the following : a) Ultimate tensile strength, c) Modulus of elasticity, d) Percent elongation and e) Percent reduction in area. The following data collected from tensile test of a metal bar diameter 20 b) The fracture strength, Force - kN 75 90 | 105 120 131 125 110 25 50 4.7 Extension-mm 0.02 0.04 0.06 0.20 - 0.60 1.60 3.00 4.0 Fracture
What value can not be found from the stress-strain graph? Please select one:a. Modulus of elasticityb. Disgracec. Toughnessd. Poisson ratioe. Yield strength
70% 5. Fatigue data of steel is showed in the following stress-cycle curve. Write down the values of steel endurance limit and steel fatigue strength at 10 cycles in the spaces provided below. 5.1. Steel Endurance Limit: ksi 5.2. Steel Fatigue Strength at 105 cycles: ksi SN Curve 50 45 40 Steel 35 30 Aluminium 20 15 10 10 10 10 10 Number of cycles 10 10 10 Page 5 of 6 (s) ssans
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. Tensile stress-strain diagram 450 400 350 300 250 200 150 100 NO 50 0.05 0.1 0.15 0.2 0.25 0.3 0 35 0.4 Strain 300 EN Stress (Mpa)
Correct one
1. Suppose that you have measured the strain aging kinetics of a high-strength low-alloy (HSLA) steel and obtained the following results: Aging Temperature (°C) Aging Time (min) ΔΥ (MPa) 150 240 40 130 1800 40 Determine (using a mathematical rather than graphical approach) the time necessary to obtain a strengthening increment, AY, of 40 MPa at an ageing temperature of 120°C. State any assumptions made in order to arrive at your approximation.
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. Stress-Strain Diagram 1200 1000 800 1000 600 800 600 400 400 200 200 0.005 0.01 0015 0.02 0.025 003 0.1 0.0s 0.15 0.2 025 Strain (mm/mm) Select one: O 0.2% O 19% O 3% 25% O 0.5% Stress (Mpa)
Load (N) Elongation (mm) In a tensile test of stainless steel, the following data were obtained: 7,200 11,250 13,500 16,200 18,900 20,200 20,700 13,200 24.90 0.0 0.505 2.03 5.08 10.16 15.24 21.80 The dimensions of the cylindrical specimen were initial length L₁= 50.8 mm and initial area A₁ = 35.8 mm² and the area at fracture was Ar = 10.0 mm². Plot the stress-strain diagram and determine the following: a) Modulus of elasticity b) The yield strength at a strain offset of 0.002 c) Ultimate strength d) Fracture strength
A tensile test specimen of 1045 hot-rolled steel having a diameter of 0.505 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the ultimate strength. Stress (ksi) 60 50- 40- 30- 20 10- 0 0 0 Upper scale O 66 ksi 28 ksi O 72 ksi O 53 ksi O 62 ksi Lower scale. 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.002 0.004 0.006 0.008 0.010 0.012 0.014 Strain (in./in.)
Calculate the ductility of this steel alloy in %EL.
From the shear stress - shear strain diagram shown below, all the following are true except: Shear Stress (MPa) 500 450 400 350 300 250 200 150 100 50 0. 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 Shear Strain (rad) Shear Stress-Strain Curve for Brass Select one: O a. Shear stress and Shear strain are 430 MPa and 1.72 rad at fracture. O b. Shear stress and Shear strain are 250 MPa and 0.05 rad at Yielding. Oc. The elastic zone ends at a shear stress of 400 MPa and shear strain of 1 rad Od. The ultimate Shear stress and Shear strain are 430 MPa and 1.72 rad.