6. Personal Protective Equipment a. A brief list of the PPE that workers must wear while conducting the site servicing works.

Q: Hand/Power Tool Demonstration and Procedure for safety  Demonstrate the ability to identify hazards…

A: Inability to identify or acknowledge hazards that are present or could have been expected is one of…

Q: Apart from the ambient air temperatures, list two factors that would be considered to select the…

A: Performance grade (PG) bitumen cement is basically used for the enhancement of the design life of…

Q: The CalOSHA Construction Safety Orders is an extensive regulatory program that cover all safety…

A: The expenses of doing business may be decreased and workplace diseases and injuries can be avoided…

Q: SITUATION I: A built up beam is made up of 1250 mm x 9 mm web section and two flange sections of 620…

A: Answer (1) Calculation of Elastic Section Modulus of the given beam Since the section is symmetrical…

Q: Question #14, Case 4: HVAC units The general contractor on this project chose not to purchase the…

A: HVAC equipment can be purchased directly from the manufacturer instead of through a mechanical…

Q: Discuss about Durability-Related Serviceability Limits

A: The limit state method accounts for the design of structure assuming that it has reached its state…

Q: Observe several construction sites and ascertain details oftheir safety program. If possible, attend…

A: As a construction site trainee engineer, I visited more than 5 construction sites in the past 1…

Q: How should they be resolved? a. Improper Electrical Wiring b. Plumbing Problems c. Minor Structural…

A: To fix the problem, turn off the power to the device, then disconnect the wires and either clip off…

Q: Analyze the construction of the duct system including insulations, methods of duct design and the…

A: Ducts There are  various type of modern design which is used as a part of ventilation in the…

Q: Please answer use nscp 2015 asap

A:

Q: What are the objectives of an Automatic blackboard/whiteboard cleaner system?

A: Automatic blackboard/whiteboard cleaner system is designed to save a lot of time and unnecessary…

Q: An ideal settling basin is designed with surface overflow rate (SOR) of 1 m³/m²/h. Particles have…

A: Given data- An ideal settling basin- Surface overflow rate- SOR = 1 m3/m2/h, To Find- The value of…

Q: Checklist that will be used in the selection of the material. Specify all criteria, diagnostic…

A: Introduction : This paper is designed to provide guidelines on good manufacturing practise (GMP) for…

Q: Describe the checks to be carried out to ensure that tools and equipment are in full working order,…

A: The check on safety equipment is an essential in addition with repairing and servicing.

Q: Identify the plumbing items fitted in the school. 2. Make a list of the identified plumbing items.…

A: These type of systems are used to provide the water facilities to the building. This water can be…

Q: Identify three factors that should motivate a contractor to have a safeoperation and a good safety…

A: Introduction:Maintaining safety and running a safety program is a must in every work sites. To…

Q: Workers who are designated as "unqualified:" a. Do not need any training. b. Must become "qualified"…

A:

Q: Define Stress Corrosi

A: Stress Corrosion is also known as Stress Corrosion Cracking. Stress Corrosion occurs when a material…

Q: Create your own Workplace Housekeeping Inspection Checklist for a NETWORK /CABLE Company with the…

A: Checklist for a CABLE Company  Floors and Other Areas Are floors clean and clear of waste? Are…

Q: Find the cam diameter and actual volume displaced? Volumetric efficiency 1420 rpm, e = 14.67 mm, L =…

A: Volumetric efficiency, ηv=91.87%=0.9187 Vane pump speed, N=1420 rpm Eccentricity, e=14.67 mm=0.01467…

Q: Problem # 01: If F₂ =30lb and Fc =45lb, determine the resultant moment about the bolt located at A…

A:

Q: 2. For the given system below, find the reactions exerted by the pin and the roller on the beam.…

A: Given data in question  Overhanging beam  Span member length  UDL UVL Point load  To find out…

Q: USE NSCP 2015 Assume a concrete cover of 40mm, 10mm stirrups and clear distance between layers of…

A: Given- Concrete and steel stresses at C=

Q: Question:  A construction company having 02 floors height & around 15 rooms , occupied by around…

A:

Q: Write Safety Work Statement of any potential hazard in the construction site

A: Introduction- Construction site safety is a component of development activities that serve to…

Workplace Safety

A workplace can be referred to as a space where people work together for the accomplishment of a common goal of the organization. Here, people can be a worker, an employee, and an employer. A person can be said to be an employer if he/she gets the job of organizational goal accomplishment through other persons, and that person gets paid for his/her service. All employees can also be referred to as workers. An employer may also hire workers of other categories which require specialized skills to finish a work. Both employees and workers along with the employer form the primary occupants of a workplace.