6. A truss ABC is subjected to a load F=10KN at pin D. The outside and inside diameters of bar AB are D=50mm and d=40mm respectively. The material is Q235 steel with E=200GPA, Ap=100 and n=3. Check the stability of bar AB. 1500 500 B 30°

6. A truss ABC is subjected to a load F=10KN at pin D. The outside and inside diameters of bar AB are D=50mm and d=40mm respectively. The material is Q235 steel with E=200GPA, Ap=100 and n=3. Check the stability of bar AB. 1500 500 B 30°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 92 GPa] with a cross-sectional area of A₁ = 680 mm². Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁=900 mm., L2=600 mm., a=580 mm., b=310 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i i L₁ L2 (2) B C MPa, 0₂ = mm. i D MPa
etermine the elongation of a 0.5-in, dianeter sterl bar The elastic modulus of the steel bar is 27000 kar. 2000 Ib 10 ft
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 340 mm2 and a length of L1 = 3.6 m. Rod (2) has an area of A2 = 315 mm2 and a length of L2 = 1.2 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 60 kN is applied to the rigid bar at D, determine:(a) the normal stresses in rods (1) and (2)(b) the magnitude of the downward deflection of the rigid bar at D.
The brass rod AB is fixed connected at A. When the temperature is T₁-50 °C, there is a 3 mm gap between its end (point B) and the wall C. The cross-sectional area of the rod is 10 cm². Ignore the weight of the bar. The temperature is now increased to T₂-130 °C and the rod AB is pushing against the wall at C. Ebr = 100 GPa, abr = 20 x 10-6/°C Fallow 70 MPa L = 3m A 3 m B/C с 3 mm a. Draw a FBD for when the temperature is increased to T₂ and write down the force balance for this scenario. Call the reactions at FA and FC. Ton =1) und prit brolim volgen Aistis Intelesa si s b. State the compatibility condition and solve for the reactions at A and C.
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 109 GPa] with a cross-sectional area of A₁ = 530 mm². Bar (2) is an aluminum alloy [E = 64 GPa] with a cross-sectional area of A2 = 330 mm². A concentrated load of P = 67 kN acts on the structure at D. Assume L₁=740 mm., L₂=500 mm., a=660 mm., b=310 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection VD of point D on the rigid bar.
10. The rigid bar below is supported by axial bar (1) and by a pin connection at C. Axial bar (1) has a cross-sectional area of A₁ = 275 mm², an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of a = 11.9x 106/°C. The pin at C has a diameter of 30 mm. After load P has been applied and the temperature of the entire assembly has been increased by 31°C, the total strain in bar (1) is measured as 975 μe (elongation). Determine: (a) the magnitude of load P. (b) the shear stress in pin C. 275 mm Connection detail (1) Rigid bar 540 mm 135 mm 260 mm
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN